3.2 Inch Touch Screen
- Version: V4.0
- Resistive touch.
- Dimension: 3.2 inch.
- Operating Voltage: DC 5V.
- Driver: XPT2046.
- Resolution: 240 x 320.
- Compatible with any version of the raspberry pie
- Drivers provided (works with your own Raspbian/Ubuntu/Kali)
- Supports FBCP software driver as well, allows to config software resolution and set up dual-display
- Comes with three buttons for easy application
- Play videos (supports multi formats, MP4, and so on)
- Take photos by touching
- Support software keyboard (system interaction without keyboard/mouse)
- The Raspbian system, have the following features:1. Take pictures (17 kinds of camera mode) 2. Support soft keyboard (from the mouse and keyboard can control the system) 3. Surfing the Internet
- Dimension: 10 x 8 x 4 cm
- Weight: 150 Grams
YF G1 Water Flow Sensor
- Working Voltage: DC 4.5V
- Working Voltage: DC 5V~18V
- Flow Rate Range: 2~100L/min
- Water pressure resistance: = >2MPa
- Operating Temperature: = -20~85C
- Insulation resistance: = >100MΩ
- Characteristics of Flow pulse: f=(4.8*Q) Q=L/Min
- Accuracy: ±3%
- Compact, Easy to Install
- High Sealing Performance
- High-Quality Hall Effect Sensor
- RoHS Compliant
SIM800A Quadband GSM / GPRS Module convertible as Shield for Arduino
- Quad-Band GSM/GPRS 850/ 900/ 1800/ 1900 MHz.
- GPRS class 2/10.
- Input Voltage: 9V-12V DC.
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
- Configurable baud rate.
- Built-in SIM Cardholder.
- Built-in Network Status LED.
- 5V interface for direct communication with MCU kit.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Low power.
- SMA connector with GSM L Type Antenna.
- Headphone jack for audio out.
- Li-Po battery 3.7-volt pins for supply.
- Li-Po battery USB charger (3.7volts).
- CP2102 port for communication with a laptop.
USB Blaster ALTERA CPLD/FPGA Programmer
- Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data.
- Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000, and MAXII.
- FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K, and FLEX10K, etc.
- Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc.
- Enhanced configuration devices: EPC1, EPC4.
- Supports 3 download modes: AS, PS, and JTAG.
- Support and Nios II embedded soft core processor communication and debugging Rev.C latest version Hardware. Support jtag_uart.
- Speed is 6 times faster than parallel port download cable ByteBlasterII.
- Easy to use: MiniUSB interface, easy connection, two status indicator makes debugging more comfortable.
- Fully compatible with ALTERA USB Blaster, functionality and performance are the same as ALTERA original download cable.
- Operating Voltage: 1.5～5V JTAG IO Voltage.
- System configuration: Windows XP, Windows Vista, Windows7, USB interface.
5V Wireless Power Supply Module Wireless Charging Module Wireless Transmission Module
- Magnetic-Coupled Resonance Technology
- Transmitting Voltage: 5V
- Output Power: 36W
- Output Voltage & Current: 5V, 3A
- Coil Size: outer diameter 82mm; inner diameter 30mm
- Transmitting Module Size: 17mm*30mm
- Receiving Module Size: 30mm*54mm
- Insulation Coil
- Compact Design
- Stable power supply
- Insulation Coil
- Space-saving design
SD Card shield V4.0 for Arduino UNO
- Standard SD card, SDHC card and TF card compatible
- 3.3v and 5v logical voltage compatible
- 2.6-3.6v DC power supply
- UART Grove & I2C connection compatible
- Fully supported SD Library
- Minimal number of SPI port
- Jumpers provided for configuring Arduino SPI port pins
- Onboard toggle switch for SD card select type
- Truly stackable
- Prototype expand Library support
- Size: 53mm x 47mm
- Weight: 35g
PN532 NFC MODULE
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI, and HSU (High-Speed UART)
- I2C / UART: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance: 5cm-7cm
- Easy to change mode: with a small SMD Toggle Switch
- Longer distance: the reading distance becomes 5~7cm,
- On-board level shifter, Standard 5V TTL for I2C and UART 3.3V TTL SPI
- Work as an RFID reader/writer
- Work as a 1443-A card or a virtual card
- Support NFC with Android phone
- Small size
- Dimensions: 42.7*40.4*4mm
UNO R3 +WiFi ATmega328P+ESP8266 Module CH340G Compatible For Arduino Uno
- Microcontroller: ATmega328IC
- Wi-Fi: ESP8266
- USB-TTL converter: CH340G
- Power Output: 5V-800mA
- Power input USB: 5V (500mA max.)
- Power input VIN/DC Jack: 9-24V
- Power Consumption: 5V 800mA
- Logic Level: 5V
- WiFi: 802.11 b/g/n 2.4 GHz
- USB type: Micro USB
- USB Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O Pins: 14
- Analog I/O pins: 6
- Memory Size: 32Mb
- Interface Type: serial
- Operating temperature: −40С°/+125С°
- Dimensions (L×W)mm: 53.34×68.58
Bluetooth Relay Shield
LOLIN32 V1.0.0 ESP32 Rev1 Wifi Bluetooth Board
FlexiForce Tekscan A502 Sensor
- Thickness - 0.203 mm (0.008 in.).
- Length - 81.3 mm (3.20 in.)**.
- Width - 55.9 mm (2.20 in.).
- Sensing Area - 50.8 mm x 50.8 mm (2 in. x 2 in.).
- Connector - 2-pin Male Square Pin.
- Substrate - Polyester.
- Pin Spacing 2.54 mm (0.1 in.).
- Standard Force: 222 N.
- Temperature Range (Low): -40 °C.
- Temperature Range (High): 60 °C.
- Thin and flexible.
- Ideal for prototyping and integration.
- Easy to use.
