Micro DC 3-6V Submersible Pump Mini water pump
L293D MOTOR DRIVER
- Can be used to run two dc motors with the same IC
- Speed and direction control is possible
- Supply voltage: 4.5 V to 7V
- Motor voltage: 4.5 v to 36v
- Maximum peak motor current: 1.2 A
- Maximum continuous motor current: 600 milli ampere
- Screw terminal connectors for easy connection
- Transition time: 300 ns (at 5v and 24v)
- High noise immunity inputs
- Automatic thermal shutdown
- Available in 16 pin DIP, TSSOP, SOIC package
- Dimension: 48*34*14mm
- Weight: 15gm
Coreless Drone Motor
Servo Mount Bracket for SG90 MG90
GT2 20 tooth bore 8mm width 10mm pulley
SERVO MOTOR SG9G
1000 RPM – 12V CS DC Geared Motor
Single Phase CS DC Geared Motor-150 Rpm
300 RPM 12V DC CENTRE SHAFT GEAR MOTOR
Single Phase CS DC Geared Motor-30 Rpm 12V
500 RPM CS Gear Motor
Single Phase CS DC Geared Motor-60 Rpm12v
CS DC Geared Motor 150 RPM
CS DC Geared Motor 300 RPM
CS DC Geared Motor 100 RPM
CS DC Geared Motor 30 RPM
CS DC Geared Motor 500 RPM
CS DC Geared Motor 60 RPM
50Kg Pressure Micro Scale Weighing Sensor
- Capacity : 50.kg
- Output Sensitivity (mv/v): 1.0±0.1.
- Nonlinearity (%FS): 0.03.
- Repeatability (%FS): 0.03.
- Input Resistance: 1000. Ω
- Insulation Resistance : ≥5000.MΩ
- Alloy Steel wired weighing load cell
- High Accuracy
- Simple Structure & Easy Installation.
- Internal 1000 Ω half-bridge strain gauge load cell, the range is 50kg, half-bridge structure
- You can use multiple load sensors simultaneously to increase the capacity range, Parallel use to add additional capacity.
CS DC Geared Motor10 rpm
12V DC Geared Motor 2000 RPM
Aluminium Flexible Coupling Coupler Helical Shaft (5 x 5 mm)
- Material: Aluminium.
- Bore Diameter d1: 5 mm.
- Bore Diameter d2: 5 mm.
- Torsional stiffness: Zero backlash.
- One piece construction.
- Corrosion resistance and High Durability
- One piece construction with long-lasting performance
- Torsional stiffness: Zero backlash
- Low moment of inertia offering constant velocity
49TYD-500 Synchronous 5 RPM AC220/240V AC Motor
Center Shaft Motor 3.5 RPM
CS DC Geared Motor 3.5 RPM
A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
Minebea 16PU-M202 Bipolar Stepper Motor
- Step angle 3.75 degree
- Phase current: 0.6 ampere
- Step Angle: 3.75 Degree +/- 5%
- Drive Sequence: Bipolar
- Rated Current per Winding: 0.6 A
- Winding Resistance: 5E5
- Holding Torque Nm (Kg-cm): 0.064 (0.65)
- Rotor Inertia (Kg-cm2): 0.015
- Rated Voltage: Max 40V DC, 12V Typical
- Flange Size: 56.5 mm
- Shaft (with coupling spur gear): 5mm
- Connecting Wire Length: 30 cm
- Holding Torque: 0.074 nm