BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit
- Input voltage: 6V-27V
- Maximum current: 43A
- Input level: 3.3-5V
- Control mode: PWM or level
- Duty cycle: 0-100%
- Double BTS7960 large current (43 A) H bridge driver
- 5V isolate with MCU and effectively protect MCU
- 5V power indicator on board
- Four lines from MCU to driver module (GND. 5V. PWM1. PWM2)
- Reverse the motor forward, two PWM input frequency up to 25kHZ
- Two heat flow passing through an error signal output
- Dimension: Approx. 4 * 5 * 1.2cm
NEMA 17 5.5 kgcm
- Step Angle : 1.8°
- Holding Torque : 5.5 KgCm
- Operating Voltage : 12 - 16 volts
- Supply Current (A) :1.5 Ampere
- Number of Leads : 6
- Inductance : 5.5 mH
- Resistance : 2.8 Ohms
- Weight (gm) : 363
- Detent Torque (kg-cm) : 2.6
- Frame Size (mm) : 42 x 42
- Inductance Accuracy : ±20%
- Resistance Accuracy : ±10%
- Step Angle Accuracy : ±5%
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 22
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
DYS Motor D2826 1100KV
- Item name: D2826 1100KV
- Voltage: 4V~14.8V
- Battery: 2~4s LiPoly
- Max watt: 102
- Max Current: 19A
- Suggested prop: 9045
- Pull: 660g
- Shaft: 3.17mm in Diameter
- Thrust: 1050g (9045 prop/4s)
- Efficiency: <4g/W
- Suggested Propeller: 8x6(2s) 7x4(3s)
- ESC: 30A
- Shaft: M5
- Pull: 660g
- Motor Mount Holes: M3 x 16/19mm
- Dimensions: 26.2 × 27.7mm
- Weight: 51g
NEMA 17 1.6 kgcm
- Operating Voltage : 12~16 V
- Step Angle : 1.8°
- Holding Torque : 1.6 KgCm
- Operating Voltage : 12 - 16 volts
- Supply Current (A) :0.31 Ampere
- Number of Leads : 6
- Frame Size (mm) : 42 x 42
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 20
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
RS-37-555 Side Shaft Geared Motor – 60 rpm 12V DC
RS-37-555 Side Shaft Gear, Geared Motor 500 rpm 12v DC
RS-37 300 RPM High Torque Side Shaft DC Geared Motor
- Nominal Voltage: 12v
- Torque Rated: 39 N-cm
- Shaft Diameter: 6mm (with internal hole)
- Shaft Length:30mm
- Gearbox diameter: 37
- Length:80mm
- Voltage : 9 to 18 No-load current : 500 mA(Max)
- Load current: 3 A(Max)
- It has a sturdy construction.
- Comes with a Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
- Weight : 300 gms
RS-37 High Torque Side Shaft DC Geared Motor 30 RPM
- Nominal Voltage: 12v
- Torque Rated: 400 N-cm
- Shaft Diameter: 6mm (with internal hole)
- Shaft Length:30mm
- Gearbox diameter: 37
- Length:80mm
- Voltage : 9 to 18 No-load current : 500 mA(Max)
- Load current: 3 A(Max)
- It has a sturdy construction.
- Comes with a Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
- Weight: 300 gms
RS-37 High Torque Side Shaft DC Geared Motor 200 RPM
- Nominal Voltage: 12v
- Torque Rated: 70 N-cm
- Shaft Diameter: 6mm (with internal hole)
- Shaft Length:30mm
- Gearbox diameter: 37
- Length:80mm
- Voltage : 9 to 18 No-load current : 500 mA(Max)
- Load current: 3 A(Max)
- It has a sturdy construction.
- Comes with a Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
- Weight : 300 gms
RS-37-555 Side Shaft Gear, Geared Motor 100 rpm 12v DC
- Voltage : 6v to 15v
- RPM:10 (at 12v)
- Nominal Voltage: 12v
- No- Load Current : 200mA
- Full Load Current:3000mA
- Full (Stall) Load Torque : 12 kg cm
- It has a sturdy construction.
- Comes with a Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
RS-37-555 Side Shaft Gear, Geared Motor 10 rpm 12v DC
- Voltage : 6v to 15v
- RPM:10 (at 12v)
- Nominal Voltage: 12v
- No- Load Current : 200mA
- Full Load Current:3000mA
- Full (Stall) Load Torque : 30 kg-cm
- It has a sturdy construction.
- Comes with a Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.
JOHNSON MOTOR HIGH TORQUE DC GEARED 12V 600RPM – GRADE A
- 600RPM 12V DC motors with Metal Gearbox and Metal Gears
- 18000 RPM base motor
- Holding Torque: 4.53kgcm
- 6mm Dia shaft with M3 thread hole
- Gearbox diameter 37 mm.
- Motor Diameter 28.5 mm
- Length 63 mm without shaft
- Shaft length 30mm
- 180gm weight
- No-load current = 800 mA, Load current = upto 7.5 A(Max)
- Recommended to be used with DC Motor Driver 20A or Dual DC Motor Driver 20A
- Grade A Quality branded Johnson DC Motor.
- It has a sturdy construction.
- Comes with Rear shaft for encoder mounting
- Shaft equips metal bushes for long life.
- It comes with High-Quality gears.
- The shaft has a hole for better coupling.