40A DC MOTOR SPEED REGULATOR PWM CONTROLLER 2000W
- Speed controller model: 40A PWM DC motor speed regulator
- Operating voltage: 10V TO 50V
- Peak current: 40A
- Control power: 0.01-2000W
- Quiescent current: 0.025A
- PWM regulation: 5-100%
- PWM frequency: 12KHz
- Operating temperature: -20 degree to 40 degree Celsius
- Stability in working
- High efficiency
- potentiometer used for speed adjustability
- Dimension: 9*5.1mm
- Weight: 95gm
PWM DC Motor Speed Controller 20A
- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward /Stop / Reverse
- Reverse polarity protection: Yes.
- Suitable Motor: DC brush motors.
A2212 BRUSHLESS DC MOTOR 1800kv BLDC
- KV: 1800
- No load Current : 10 V : 0.5 A.
- Current Capacity: 12A/60s
- No Load Current @ 10V: 0.5A
- Of Cells: 2-3 Li-Poly
- Motor Dimensions: 27.5 x 30mm
- Shaft Diameter: 934;3.17mm
- Shaft diameter : 3.175mm.
- Minimum ESC Specification: 18A (30A Suggested)
- Thrust @ 3S with 1045 propeller: 1000gms approx
- Thrust @ 3S with 0945 propeller: 650gms approx
- Thrust @ 3S with 0845 propeller: 550gms approx
6V 12V 24V 8A PWM DC Motor Speed Controller CCM5D Digital Display LED Motor Controller Speed Regulator
- Input Supply Voltage: 6V-30VDC
- Continuous Current (A): Rated current 5A (8A MAX, cannot be prolonged)
- Maximum Output Power: 240W
- LED display the duty ratio: 0-100%
- PWM Frequency: 16khz
- Duty Cycle adjustable: 0%-100%
- Dimensions: 78*42*25mm
- The display range of 3-digit LED display is "000"-"100".
- Adjustable speed range is 0%-100%
- Fine workmanship and good performance.
- Easy to use.
- Long service life.
- Suitable for the DC motor (or DC load) within 5A, Peak current 8A.
- Incorporate a push key. Push closed, and then push open
DC 6-30V 6V 12V 24V 5A PWM Motor Speed Controller with Digital Display
- Material: ABS
- Colour: Black
- Input power supply voltage: 6V-30V DC
- Output current: rated current 5A (maximum 8A, can not be extended)
- PWM frequency: 13kHz
- Duty cycle adjustable: 0%-100%
- Adjustable speed range: 0%-100%
- Fine workmanship and good performance.
- Digital display for duty ratio input
- Easy to use.
- Long service life.
- Suitable for the DC motor (or DC load) within 5A, Peak current 8A.
- Dimension: 78*42*25mm
A2212 BRUSHLESS DC MOTOR 1000KV
- Motor KV: 1000
- Operating voltage: 7.2V to 12V (2 to 3Li-poly or 6to10 NiCad)
- LiPO Batteries: 2S-3S
- No-load Current: 10 V: 0.5 A.
- Current Capacity: 12A/60S
- Maximum current:13Amp for 60Sec
- Maximum Watts:150 Watt
- Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
- Prop Adapter is quality tested
- Minimum ESC Specification: 18A (30A Suggested)
- Maximum operating temperature: + 80°C
- Complete speed control because of a three-phase connection.
- Long-life as there are no moving contact
- Thrust @ 3S with 1045 propeller: 800gms approx
- Thrust @ 3S with 0945 propellers: 475gms approx
- Thrust @ 3S with 0845 propellers: 475gms approx
- Motor Dimensions: 27.5 x 30mm
- Weight of motor:50-60 grams
Brushless DC Motor BLDC Motor
- Less overall maintenance due to absence of brushes
- Reduced size with far superior thermal characteristics
- Higher speed range and lower electric noise generation.
- It has no mechanical commutator and associated problems
- High efficiency and high output power to size ratio due to the use of permanent magnet rotor
- High speed of operation even in loaded and unloaded conditions due to the absence of brushes that limits the speed
- Smaller motor geometry and lighter in weight than both brushed type DC and induction AC motors.
- Long life as no inspection and maintenance is required for commutator system
- Higher dynamic response due to low inertia and carrying windings in the stator
- Less electromagnetic interference
- Low noise due to absence of brushes
N20 Model – 100 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Motor Type: Center Shaft DC Geared Motor
- RPM:100
- Reduction ratio - 1:298.
- Nominal Voltage - 6v
- Voltage Range - 2v to 12v
- No load Current - 80mA
- Stall Current - 1640mA
- Stall Torque - 3500 g-cm
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long lasting , not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
MG90S 9G Metal Gear Micro Servo Motor
- Modulation: Analog
- Gear Type: Metal
- Stall Torque@ 4.8V: 2.20 kg-cm
- Stall Torque@ 6.0V: 2.50 kg-cm
- Speed at 4.8V: 0.11 sec/60°
- Speed at 6.0V: 10 sec/60°
- Weight: 49 oz. (14.0 g)
- Dimensions: 23.1*0.48*1.14
- Rotation/Support: Dual Bearings
- Rotational Range: 180°
- Pulse Cycle: 20 ms
- Pulse Width: 400-2400 µs
N20 Model – 500 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio - 1:30.
- Nominal Voltage - 6v
- Voltage Range - 3v to 12v
- RPM - 500
- No-load Current - 40mA
- Stall Current - 550mA
- Stall Torque - 400 g-cm
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
XB NEMA 34 (86mm-S) Coupling 12.7x8mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Large Bore Diameter: 12.7mm
- Small bore diameter:8mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 12.75mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines
XB NEMA 34 (86mm) Coupling 12.7×12.7mm
- Material: Aluminum alloy hubs and elastomeric polyurethane spider.
- Product Type: Clamp-style jaw coupling without keyway.
- Bore Diameter: 12.7*12.7mm
- Number of Screws: 2 each.
- Angular Misalignment: +/-1°.
- Parallel Misalignment: +0.20mm/-0.20mm .
- Maximum Rotational Speed: 6500RPM.
- Suitable for Nema 23 Stepper Motor or for any motor/rod having an 12.75mm diameter
- Widely used in motors, stepper motors, encoders, and servo machines.