6 PIN 128*64 OLED 0.96” BLUE
- Resolution: 128*64
- Visual angle>160
- Input voltage:3.3V to 6V
- Compatible I/O level:3.3v, 5v
- Only need 2 I/O port to control
- Driver IC: SSD1306
- Module volume:27*27*4.1mm
- Working temperature: -30 degree to 70 degree
- Full compatible with Arduino
- Configured for SPI protocol and can be easily changed to IIC
4 PIN 128*64 OLED 0.96” WHITE
- High resolution: 128*64
- Driver IC: SSD1306
- Input voltage: 3.3v to 6 v
- Ultra-wide viewing angle >160 degree
- Display color: white
- Super low power consumption
- Support a wide range of input
- Performs without the need for a backlight
- Compatible I/O level: 3.3v, 5v
- Fully compatible with Arduino
- Interface: I2C
- Working temperature: -30 degree to 70 degree
- Dimension: 9*9*9cm
- Size: 99gm
TowerPro SG-5010(180° Rotation)
4 Inch 0.26A 230V AC Fan
DC 6V AIR PUMP SMALL
PIC16F887 Microcontroller IC
- Architecture: 8 bit
- Program Memory (Flash): 14 kB
- RAM: 368 byte
- Internal Oscillator: 8 MHz, 32 KHz
- ADC: 1 (14 channels)
- of Pins: 40
- Voltage: 2V - 5.5V
- Precision Internal Oscillator:
- Power-Saving Sleep mode
- Wide operating voltage range (2.0V-5.5V)
- Industrial and Extended Temperature range
- Power-on Reset (POR)
- Power-up Timer (PWRT) and Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR) with software control option
- Enhanced low-current Watchdog Timer (WDT) with on-chip oscillator (software selectable nominal 268 seconds with full prescaler) with software enable
- Multiplexed Master Clear with pull-up/input pin
- Programmable code protection
- High Endurance Flash/EEPROM cell:
- Program memory Read/Write during run time
- In-Circuit Debugger (on board)
CS DC Geared Motor 6 RPM
3S BMS BOARD 25A
- Charging Voltage: 12.6V DC CC/CV
- Balance Voltage for Single Cell: 4.2V
- Max Continuous Charge/Discharge Current: 25A
- Overcharge voltage range: 4.25-4.35v + 0.05v.
- Over discharge voltage range: 2.3-2.7v + 0.05v.
- Operating current: 0 – 25A.
- Operating temperature: -40 – +50℃.
- Instantaneous current: 35 – 40A.
- Storage condition: -40 – +80℃.
- Quiescent current: less than 30uA.
- Balance current: about 40 – 50mA.
- Effective life: more than 30000 hours.
- Internal resistance: less than 100m ohms.
- Short-circuit protection: protection, delayed self-recovery.
L9110 DC Stepper Motor Driver Board H-Bridge
- Low static work current
- Power supply voltage: DC2.5-12V
- Each channel has 800mA continuous current output
- Low saturation pressure drop
- TTL/CMOS output level compatible can be connected directly to the CPU
- Output built-in clamping diode, apply to the perceptual load
- Control and drive integrated into IC
- Have pin high-pressure protection function
- Working temperature: 0-80 °C
RB NEMA 17 (42mm) Coupling 5×6.35mm
5V Stepper Motor 28BYJ-48 with ULN2003
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- No of phase: 4
- Speed variation ratio: 1/64
- Pull-in torque: 300 gf.cm
- Friction torque: 600-1200 gf.cm
- DC resistance: 50Ω±7% (25°C)
- Insulated resistance: >10MΩ (500V)
- Insulated power: 600VAC/1mA/1s
- Rise in Temperature <40K(120Hz
- Noise <35dB(120Hz,No load,10cm
- Stepper motor with a standard interface, when used directly pluggable.
- Four-phase LED indicator which indicates the status of the stepper motor work.
- Compact size stepper motor perfect for small robotics applications.