Showing 1–12 of 16 results

“PWM Generator Module for Stepper Motor Driver with Forward and Reverse Function “

₹1,550.00 inc. GST
  • Board can be used to generate PWM signals for the stepper motor driver
  • Operating Voltage: 12VDC
  • Three Frequency Range
  • Forward and Reverse Function.
  • It has three frequency ranges selectable via onboard jumpers.
  • Frequency can be measured via PUL and common cathode (GND) ports.
  • The board has two sets of power input

A3967 STEPPER MOTOR DRIVER

₹300.00 inc. GST
  • A3967 precision micro-stepping driver
  • Power supply: 7v to 30v
  • Logic voltage: 5v to 3.3v
  • Higher the voltage higher the torque at high speed
  • Adjustable current control from 150Ma/ phase to 750ma phase
  • Automatic current decay mode detection/selection
  • Fast, slow, and mixed current decay modes
  • Internal UVLO and thermal shutdown circuitry
  • Crossover current protection
  • Micro stepping resolution to full, half, quarter, and eighth steps by broken out MS1 and MS2 pins.
  • Compatible with Arduino, GRBL G-Code interpreter for driving3-axis CNC machines
  • Salington sink drivers used
  • Compactible with 4, 6,8 wire stepper motor of any voltage
 

A4988 Stepper Motor

₹160.00 inc. GST
  • Operating voltage supply: 8 V to 35 V
  • Continuous current per phase: 1 Amp
  • Maximum current per phase: 2 Amp
  • Minimum logic voltage: 3V
  • Maximum logic voltage: 5.5V
  • Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
  • Logic Voltage supply: 3.3 V to 5 V
  • Compatible with 3V3 and 5V microcontrollers
  • Our Board comes with 0.1 Ohm Sensor resistors
  • Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
  • The Correct current decay mode (fast decay or slow decay) is selected by chopping the control
  • Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
  • Short-to-ground and shorted-load protection
  • 4-layer, 2 oz copper PCB for improved heat dissipation
  • Exposed solderable ground pad below the driver IC on the bottom of the PCB

A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD

₹250.00 inc. GST
  • Operating voltage supply: 8 V to 35 V
  • Continuous current per phase: 1 Amp
  • Maximum current per phase: 2 Amp
  • Minimum logic voltage: 3V
  • Maximum logic voltage: 5.5V
  • Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
  • Compact size, easy to install and use.
  • All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
  • Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
  • E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.

BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit

₹950.00 inc. GST
  • Input voltage: 6V-27V
  • Maximum current: 43A
  • Input level: 3.3-5V
  • Control mode: PWM or level
  • Duty cycle: 0-100%
  • Double BTS7960 large current (43 A) H bridge driver
  • 5V isolate with MCU and effectively protect MCU
  • 5V power indicator on board
  • Four lines from MCU to driver module (GND. 5V. PWM1. PWM2)
  • Reverse the motor forward, two PWM input frequency up to 25kHZ
  • Two heat flow passing through an error signal output
  • Dimension: Approx. 4 * 5 * 1.2cm

DM556 Digital Stepper Motor Driver with Micro Stepping 20 to 50V 5.6A

₹4,000.00 inc. GST
  • Good high-speed performance
  • Supply voltage: +50VDC
  • Output current from 0.5A to 5.6A
  • Pulse input frequency up to 200 kHz
  • Extremely cost-effective
  • Automatic idle-current reduction
  • Self-test and Auto-configuration technology TTL compatible and optically isolated input
  • Micro step resolutions programmable, from full-step to 102,400 steps/rev
  • Suitable for 2-phase and 4-phase motors
  • Support PUL/DIR and CW/CCW modes
  • Anti-Resonance provides optimum torque and nulls mid-range instability
  • Extra-low motor noise offers excellent quietness
  • Over-voltage, over-current protection and phase error protection

L9110 DC Stepper Motor Driver Board H-Bridge

₹300.00 inc. GST
  • Low static work current
  • Power supply voltage: DC2.5-12V
  • Each channel has 800mA continuous current output
  • Low saturation pressure drop
  • TTL/CMOS output level compatible can be connected directly to the CPU
  • Output built-in clamping diode, apply to the perceptual load
  • Control and drive integrated into IC
  • Have pin high-pressure protection function
  • Working temperature: 0-80 °C

Leadshine DM320C

₹5,500.00 inc. GST
  • Supply voltage up to +30 VDC
  • Output current programmable, from 0.3A to 2.0A
  • Pulse input frequency up to 70 kHz
  • TTL compatible and optically isolated input
  • Automatic idle-current reduction
  • Suitable for 2-phase and 4-phase motors
  • Support PUL/DIR and CW/CCW modes
  • Over-voltage, over-current, phase-error protection
  • Anti-Resonance provides optimum torque and nulls mid-range instability
  • Self-test and Auto-configuration technology offers optimum responses with different motors
  • Microstep resolutions programmable, from full-step to 102,400 steps/rev
  • Support PUL/DIR and CW/CCW modes
  • Over-voltage, over-current, phase-error protection
  • Its unique features make the DM320C an ideal solution for applications that require low-speed smoothness

Leadshine DM542

₹4,500.00 inc. GST
  • Good high-speed performance
  • Supply voltage up to +50VDC
  • Output current up to 4.2A
  • Pulse frequency up to 300 KHz
  • Extremely cost-effective
  • Automatic idle-current reduction
  • 3-state current control technology
  • Self-adjustment technology
  • Pure-sinusoidal current control technology
  • TTL compatible and optically isolated input
  • 15 selectable resolutions in decimal and binary, up to 25,600 steps/rev
  • Suitable for 2-phase and 4-phase motors
  • DIP switch current setting with 8 different values
  • Support PUL/DIR and CW/CCW modes
  • Short-voltage, over-voltage, over-current protection

Leadshine DMA860E Stepper Motor Driver

₹5,700.00 inc. GST
  • Model: DMA860E.
  • Control Mode: Step & Direction.
  • Max Input Frequency: 200 kHz.
  • Input Voltage Range: 18 - 80 VAC / 24 - 110 VDC.
  • Suggested Power Supply Voltage Range: 36-90 VDC /24-60 VAC.
  • Number of DIP Switch Resolution Configurations: 16.
  • 16 selectable micro-step resolutions of 400-51,200 via DIP switches.
  • 8 selectable output current settings of 2.4 – 7.2A via DIP switches.
  • Logic Current Range: 7-16mA (10mA typical).
  • Logic Voltage Range: 4-5 VDC for pulse active high (default), or 0-0.5V for pulse active low.
  • Pulse enabled at: Rising edge.
  • Idle Current Percentage: 50 %.
  • Number of Digital Inputs: 3.
  • Step Width: 2,500 ns.
  • Minimal Direction Setup Time: 5,000 ns.
  • Isolation Resistance: 500M Ohm..
  • Ambient Temperature: 0-50°C.
  • Humidity: 40–95% RH.
  • Operating Temperature: 0-70°C.
  • Vibration: 5.9 m/s2 Max.
  • Motor auto-identification and parameter auto-configuration for optimal torque from wide-range motors.
  • Step & direction (PUL/DIR) and CW/CCW (via internal jumper set) control. Step & direction by default Multi-Stepping for smooth motor movement.
  • Opto Isolation for input control signals.
  • Soft-start with no “jump” when powered on.
  • Protections for over-voltage and over-current.
  • Dimension: 5.94 X 3.82 X 2.24 Inches.
  • Weight: 1.13 lbs.
   

Leadshine DMA860H

₹8,500.00 inc. GST
  • Input voltage: Up to +80VAC or +110VDC.
  • Output current Up to 7.2A.
  • Pulse input frequency up to 300 KHz.
  • Automatic idle-current reduction.
  • Over-voltage, over-current protection.
  • Suitable for 2-phase and 4-phase motors.
  • Support PUL/DIR and CW/CCW modes.
  • Operating Temperature : 70 C.
  • High performance, cost-effective
  • Self-adjustment technology
  • Pure-sinusoidal current control technology
  • TTL compatible and optically isolated input
  • 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
 

Minebea 16PU-M202 Bipolar Stepper Motor

₹275.00 inc. GST
  • Step angle 3.75 degree
  • Phase current: 0.6 ampere
  • Step Angle: 3.75 Degree +/- 5%
  • Drive Sequence: Bipolar
  • Rated Current per Winding: 0.6 A
  • Winding Resistance: 5E5
  • Holding Torque Nm (Kg-cm): 0.064 (0.65)
  • Rotor Inertia (Kg-cm2): 0.015
  • Rated Voltage: Max 40V DC, 12V Typical
  • Flange Size: 56.5 mm
  • Shaft (with coupling spur gear): 5mm
  • Connecting Wire Length: 30 cm
  • Holding Torque: 0.074 nm