Arduino UNO R3 Clone
Raspberry Pi 4 8GB RAM | Raspberry Pi Desktop Computer
- This Raspberry Pi 4 is integrated with a 64-bit quad-core Cortex- A72 ARM v8, Broadcom BCM2711 and runs at a speed of 1.5GHz
- The new Raspberry Pi product is equipped with Bluetooth 5.0, BLE, gigabit ethernet and has 802.11ac wireless at 2.4GHz and 5GHz
- It provides faster data transfer with two USB 3.0 ports, two USB 2.0 ports, micro SD slot for data storage and loading operating systems
- The Raspberry Pi 4 has 2 micro HDMI ports (supports 4k@60p), 2 lane MIPI DSI display port, 2 lane MIPI CSI camera port, and 4-pole stereo audio and composite video port
- Robocraze is the authorized seller of Raspberry Pi products in India
12V Wireless Charging Module
Touch Sensor For Mirror
Arduino Pro Mini
Arduino Uno R3 Clone SMD
- Microcontroller: ATmega328 SMD.
- Operating Voltage: 5V.
- Supply Voltage recommended: 7-12V DC.
- Digital I/O Pins: 14 (of which 6 provide PWM output).
- Analog Input Pins: 6.
- DC Current per I/O Pin: 40 mA.
- DC Current for 3.3V Pin: 50 mA.
- Flash Memory: 32 KB (ATmega328) of which 0.5 KB is used by the bootloader.
- SRAM: 2 KB (ATmega328).
- EEPROM: 1 KB (ATmega328).
- Clock Speed: 16 MHz.
433MH RF Module Green
- Wide input supply (2.5 V to 12V)
- Easy to integrate (V+, GND, and Data)
- The device is in deep sleep mode when the Data pin is grounded
- Very small dimension
Receiver Module specification
- Operation voltage: DC5V
- Static Current: 4MA
- Receiver frequency: 433.92MHZ; 315 Mhz
- Sensitivity：－105DB
- Dimension：30*14*9mm
- External Antenna：32CM signal wire, spiral
Transmitter Module Specification
- Operating voltage: 3-12V
- Operating frequency: 433.92MHz; 315Mhz
- Standby current: 0mA
- Operating current :20-28mA
- Transmission distance:> 500m (open to receiving plate sensitivity at-103dBm distance of more than)
- Output Power: 16dBm (40mW)
- Transfer rate: <10Kbps
- Modulation mode: OOK (Amplitude Modulation)
- Operating Temperature: -10 ℃ ~ +70 ℃
- Size: 19 × 19 × 8mm
DC-DC Booster Module 3v-20000v
- Input voltage: DC 3V Input Current: 1.5A
- Output voltage: DC20KV
- Output current: 0.05A
- Input Line Length: approx. 110 mm (red is positive)
- Output cable length: approx. 110mm
- High voltage bipolar discharge distance: 5mm
- type: pulse current
- Structure: and low voltage integrated
- Material: metal
- Color: black and black
- High-Quality Silicone Wires at Input and Output
- Small in Size
- Easy to Use
- Size: 19 x 20 x 18 mm
Thermostat Sensor 180D
Thermostat Sensor 145D
Thermostat Sensor 135D
Thermostat Sensor 125D
Thermostat Sensor 120D
Thermostat Sensor 115D
Thermostat Sensor 110D
XL4432 LORA Sensor Module
- Frequency range: 433.92M
- High sensitivity up to-121dBm
- Maximum output power: 20dBm
- Data transfer rate: 0.123-256 kbps
- FSK, GFSK, and OOK modulation mode
- 1.8-3.6V power supply
- Ultra-Thin Power Off Mode
- Digital signal strength indicator received (RSSI)
- Synchronization alarm function
- Automatic antenna connection and bidirectional switch control
- The configurable data package structure
- Before sync signal detection
- 64 bytes RX data record (FIFO)
- Low power tests
- Temperature detection and 8-bit analog to digital converter
- Operating temperature range: -20 ~ + 60 C
Thermostat Sensor 95D
Thermostat Sensor 85D
Thermostat Sensor 80D
Thermostat Sensor 75D
Thermostat Sensor 60D
Thermostat Sensor 55D
Thermostat Sensor 50D
Thermostat Sensor 45D
Induction Cooker Sensor
PICKIT-3 Programmer
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Diagnostic LEDs (power, active, status)
- Read/write program and data memory of the microcontroller
- 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
- Peripheral freeze at the breakpoint.
- Program up to 512K byte flash.