ATtiny85 Arduino-enabled Mini USB Dev Board
- Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
- Power via USB or External Source
- Onboard 5V Regulator
- Built-in USB
- 6 I/O Pins
- 8k Flash Memory (about 6k after bootloader)
- I2C and SPI (vis USI)
- PWM on 3 pins (more possible with Software PWM)
- 10-bit ADC
- ADC on 4 pins
- Power LED and Test/Status LED
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
LilyTiny (LilyPad ATTiny85)
- Program Memory Type: Flash
- Program Memory (KB) : 8
- CPU Speed (MIPS): 20
- Data EEPROM (bytes): 512
- Digital Communication Peripherals: 1-SPI, 1-I2C
- Capture/Compare/PWM Peripherals : 5
- Comparators: 1
- Temperature Range (C) : -40 to 85
- Operating Voltage Range (V): 1.8 to 5.5
- Pin count: 8
- Cap Touch Channels : 3
Arduino Mega 2560 Board
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 128 KB of which 4 KB used by the boot loader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
Arduino UNO R3 Clone
Arduino Compatible Nokia 5110 Prototype Proto Shield Expansion Board
- Supports Nokia5110 display
- Standard 0.1"x0.1" prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- Â IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- Reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
- A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
- Surface-mount chip area for up to 14 SOIC size parts
- Compatible with tiny breadboards
- Every pin is brought out
- Gold plated pads
- 2 x 0.1uF capacitors on either side for extra power stability
EYE BLINKING SENSOR
- Working Voltage +5V DC
- TTL output 5V or 0VSimple setup.
- Remote detection - no mechanical contact with the eye.
- Stray visible and IR light not affected.
- Our system does not require the restraint of the external eyelids.
- Head movement not affected.
- Excellent frequency characteristics (DC to more than 500 Hz).
- Excellent working distance (15-25 mm).
- Difficult to calibrate using common units of eye blink measurement. (e.g. mm of eyelid displacement)
LTH 1550-01 IR Transmitter Reciever module
- Type: reflective.
- Fast switching speed
- Pin count :4
- Reverse Voltage: 5 V
- Sensing Distance: 3.81 mm
- Maximum collector-emitter voltage: 30V
- Operating Temperature: -25 ° C to +85 ° C
- Maximum forward current: 1A
- Dimensions: 8.7mm (L) x 4.5mm (W) x 5.6mm (H)
- Maximum emitter-collector voltage: 5V
- Maximum power dissipation for input diode: 90mW
- Maximum collector current: 20mA
- Maximum power dissipation for output phototransistor: 100mW
- Non-contact switching
- For direct PC board or dual-in-line socket mounting
HC-06 Bluetooth Module
- Input Supply voltage: 3.6 - 6V
- Input current: 50 (mA)
- Maximum Operating Range: 10m
- Operating Frequency: 2.4GHz ISM band
- Modulation: GFSK (Gaussian Frequency Shift Keying)
- Emission power: 4dBm, Class 2
- Sensitivity: -84dBm at 0.1% BER
- Operating Temperature: -20 ~ +75 degree C
- Potter default rate of 9600, the user can be set up.
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Speed: Asynchronous: 2.1Mbps (Max) / 160 kbps, Synchronous: 1Mbps/1Mbps.
- Security: Authentication and encryption.
- Profiles: Bluetooth serial port.
Air Pressure Sensor MPX 10
- Pressure Type: Differential Sensitivity
- Operating Pressure Min: 0kPa
- Operating Pressure Max: 0-10kPa
- Minimum Supply Voltage: 3V
- Maximum Supply Voltage: 6V
- of Pins: 4Pins
- Operating Temperature Min: -40°C
- Operating Temperature Max: 125°C
- Low Cost
- Patented Silicon Shear Stress-Strain Gauge Design
- Ratiometric to Supply Voltage
- Easy to Use Chip Carrier Package Options
- Differential and Gauge Options
- Durable Epoxy Unibody Element or Thermoplastic
- (PPS) Surface Mount Package
DS1820 Temperature Sensor
- Unique 1–Wire interface requires only one port pin for communication
- Multidrop capability simplifies distributed temperature sensing applications
- Requires no external components
- Can be powered from the data line
- Zero standby power required
- Measures temperatures from –55° C to +125° C in 0.5° C increments.
- Temperature is read as a 9–bit digital value.
- Converts temperature to digital word in 200 ms (Typ.)
- User-definable, nonvolatile temperature alarm settings
- Alarm search command identifies and addresses devices whose temperature is outside of programmed limits (temperature alarm condition)
