YF-S402 High Precision Flow Meter Water Flow Sensor
- Model: YF-S402
- Minimum rated working voltage: DC 5~24V;
- working current: 15mA (DC 5V);
- Working voltage range: DC 5~18V;
- Load capability: <= 10mA (DC 5V);
- Working temperature: <= 80'C;
- Humidity range: 35%~90%RH (no frost);
- Water pressure: <1.75Mpa;
- Storage temperature: -25~80'C; Storage humidity: 25~95%RH;
- Flow range: 1~5L/min'; Frequency: 4380 pulse for 1L through the sensor
- Dimensions: 2.28 in x 1.38 in x 1.06 in (5.8 cm x 3.5 cm x 2.7 cm)
- Thread Size : G1/4"
GY-906 MLX90614ESF Contactless Temperature Sensor Module
- Small size, low cost
- Mounted on a breakout board with two types of pins
- 10k Pull up resistors for the I2C interface with optional solder jumpers
- Easy to integrate
- Factory calibrated in wide temperature range:
- Sensor temperature: -40...+125°C
- Object temperature: -70...+380°C
- High accuracy of 0.5°C over the wide temperature range
- (0...+50°C for both Ta and To) High (medical) accuracy calibration
- The measurement resolution of 0.02°C
- Single and dual-zone versions
- SMBus compatible digital interface
- Customizable PWM output for continuousreading
- Simple adaptation for 8...16V applications
- Sleep mode for reduced power consumption
DHT21 AM2301 Digital Temperature Humidity Sensor module SHT11 SHT15 Arduino
- Power: DC 3.3-5.2V
- Humidity: 0~99.9% RH
- Temperature: -20 ~ 60℃
- Precision: ±3% RH, ±0.5 ℃
- Output: Digital (1 wire)
- Accurate, durable and high quality
- 4 pin package
- Ultra-low power
- No additional components
- Excellent long-term stability
- All calibration, digital output
- Completely interchangeable
- Long distance signal transmission
- Relative humidity and temperature measurement
- Dimension: 60 x 27 x 14mm
HR202 Digital Temperature Humidity Sensor
- Working Voltage: 3.3 V-5 V
- Output AO - analog output, DO - digital output
- High-quality HR202 humidity sensor
- Comparator output signal is clean, good waveform, driving ability, more than 15mA
- Adjust the temperature distribution position detection threshold
- The output form: DO digital switching outputs ( 0 and 1 ) and AO analog voltage output
- A fixed bolt holes for easy installation
- Using a wide voltage LM393 comparator
- PCB Board Size: 3.2 cm x 1.4 cm
HCZ-H8-B Humidity Sensor, HCZ Series, 20% to 90% RH, 3 %, Through Hole, No Housing
Metal Detector Sensor
- Low battery indicator
- Multiple Modes
- VCC 9V Battery
- Logic high output with common ground
- Can detect any metal at the range of 1Cm to 3Cm, you can connect a 9V battery to make it handy
- It will not detect coins if it is in the middle of the coil, it may detect if it is close to the coil, It will not detect any type of explosives
- The metal sensor has to supply 12V from controllers and not 12V via adapter
5 Channel Infrared Reflective Sensor promixity sensor
- High-Quality Tracker Sensor
- The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced.
- Distance between each IR Sensor: 15mm
- Uses 5 sensors for best resolution
- Great useful in building fast line following and grid navigating robots
- Comes with easy to use digital outputs with a direct connection to microcontrollers
- The array has mounting holes of 3mm diameter for easy mounting
- Status LED on each sensor for the detection of black line
3 Channel Infrared White/Black Line Detection Module – Proximity Sensor
- Input voltage: 3.0 V – 5.5 V
- High accuracy for tracking Black/White lines.
- Distance sensor at the front, distance can be adjusted
- Special touch sensor design, making the robot design simple
- Output form: digital output (high and low level)
- Indicator LEDs
- Onboard potentiometer to adjust the sensitivity
- Detection distance: 0 – 4 cm (black and white line sensors), 0 – 5 cm (adjustable distance detection)
Potentiometer Membrane Magneto Pot 50mm
GSR Sensor for Grove
HB100 Microwave Doppler Radar Wireless Motion Sensor Module
