PWM DC Motor Speed Controller 20A
- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward /Stop / Reverse
- Reverse polarity protection: Yes.
- Suitable Motor: DC brush motors.
Vibration Motor
- Speed(RPM):19000
- Motor diameter: 6mm
- Shaft diameter: 0.8mm
- Shaft length: 4mm
- Rated voltage: 1.5V-4.5V
- Small Compact Size
- Metal Body
- Power: [email protected]
- Powerful Motor
Toy Motor Small
Toy Motor Small With Leaf
Coreless Drone Motor
Brushless DC Motor BLDC Motor
- Less overall maintenance due to absence of brushes
- Reduced size with far superior thermal characteristics
- Higher speed range and lower electric noise generation.
- It has no mechanical commutator and associated problems
- High efficiency and high output power to size ratio due to the use of permanent magnet rotor
- High speed of operation even in loaded and unloaded conditions due to the absence of brushes that limits the speed
- Smaller motor geometry and lighter in weight than both brushed type DC and induction AC motors.
- Long life as no inspection and maintenance is required for commutator system
- Higher dynamic response due to low inertia and carrying windings in the stator
- Less electromagnetic interference
- Low noise due to absence of brushes
Toy Motor Long Shaft
- DC 12V
- 13000 rpm motor
- long shaft high speed motor
- Suitable for toy car and other toys.
- Good heat dissipation with cooling fan
- Voltage: 12V.
- No Load Current: 0.9A
- No Load Rotate Speed: 13000r/ min. Shaft Length: 20mm/ 0.79in
- Shaft Diameter: 3mm/ 0.12in. Size: 92mm x 37mm x 37mm/ 3.62in x 1.46in x 1.46in. Net Weight: 230g/ 8.11oz. Color: Silver
BO Motor Double Shaft 200 RPM
- Shaft length: 7 mm Motor Design: Straight Dual Shaft
- Shaft Diameter: 5.5 mm
- Size: 55 x 48 x 23 mm.
- Operating Voltage: 3 to 12V.
- Current (without loading): 40-180mA.
- RPM: 200 rpm.
- Output Torque: 0.35 kg cm.
- Cost-effectiveness of the injection-molding process.
- Elimination of machining operations.
- Low density: lightweight, low inertia.
- Uniformity of parts.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Corrosion-resistance; elimination of plating, or protective coatings.
- The quietness of operation.
- Tolerances are often less critical than for metal gears, due in part to their greater resilience.
- Consistency with the trend to greater use of plastic housings and other components.
Bo Motor Double Shaft 150RPM
- RPM: 150
- Operating Voltage : 3V - 9V
- Gear materials: plastic.
- Motor types: permanent-magnet.
- Brush-type: Brush.
- Uncommitted motors: Homopolar motors.
- Magnet types: ferrite magnets.
- Torque: Approximate 2.5Kg/cm.
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- Relatively low coefficient of friction.
- Corrosion-resistance; elimination of plating, or protective coatings.
- Quietness of operation.
- Tolerances often less critical than for metal gears, due in part to their greater resilience.
- Consistency with trend to greater use of plastic housings and other components.
BO Motor B10
- Shaft length: 7 mm
- Shaft Diameter: 5.5 mm
- Size: 55 x 48 x 23 mm.
- Operating Voltage: 3 to 12V.
- Current (without loading): 40-180mA.
- Cost-effectiveness of the injection-molding process.
- Elimination of machining operations.
- Low density: lightweight, low inertia.
- Uniformity of parts.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Corrosion-resistance; elimination of plating, or protective coatings.
- The quietness of operation.
- Tolerances are often less critical than for metal gears, due in part to their greater resilience.
- Consistency with the trend to greater use of plastic housings and other components
Coreless Motor Flat
- Ultra-flat dimensions
- No cogging or preferred rotor position
- No iron losses
- Extremely low current consumption
- Low starting voltage
- Low rotor inertia for extremely fast acceleration and braking
- Extremely light and compact
- Custom systems available from design to production
- Very cost effective
- Precision gearboxes available in all sizes
Mini Disc Vibrating Motor
Generator Motor Small
DC Toy Motor
Generator Motor Big
ESC 30A BLDC Electronic Speed Controller
- Standard 30A BLDC ESC Electronic speed controller
- Input voltage: DC 6V-16.8V(2-4S Lixx)
- BEC: 5V 2amp
- Easy handling and good compatibility
- Suitable Batteries: 2-3S LiPo.
- Application: BLDC Motors, Multirotor, RC Planes et
- Running current: 30A (Output: Continuous 30A, Burst 40A up to 10 Secs.)
- Size: 36* 26* 7mm
- Weight: 32g
Bullet Connector 3.17mm
STEPPER MOTOR MINI
STEPPER MOTOR NEMA 23 7.2KG
SERVO MOTOR MG 995- 360 Degree
- Servo type: Analog Servo
- Operation Voltage : 4.8 – 7.2Volts
- Gear Type: All Metal Gears
- Operating temperature: -30 ~ + 60 °
- Dead band setting: 4 microseconds
- Rotation angle: 360°
- Torque: 4.8V: 130.5 oz-in (9.40 kg-cm),
- Speed: 4.8V: 0.20 sec/60°, 6.0V: 0.16 sec/60°
- Stable and shockproof double ball bearing design
- Connection cable is thicker.
- Equips high-quality motor.
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power
- Weight: 55g
- Dimension : 40.7 × 19.7 × 42.9 mm
SERVO MOTOR SG9G
20A PWM Motor Speed Controller DC 6 30V 6V 12V 24V 48V
A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
A2212 BRUSHLESS DC MOTOR 1800kv BLDC
- KV: 1800
- No load Current : 10 V : 0.5 A.
- Current Capacity: 12A/60s
- No Load Current @ 10V: 0.5A
- Of Cells: 2-3 Li-Poly
- Motor Dimensions: 27.5 x 30mm
- Shaft Diameter: 934;3.17mm
- Shaft diameter : 3.175mm.
- Minimum ESC Specification: 18A (30A Suggested)
- Thrust @ 3S with 1045 propeller: 1000gms approx
- Thrust @ 3S with 0945 propeller: 650gms approx
- Thrust @ 3S with 0845 propeller: 550gms approx
Worm Gear Box Reduction Motor 12V 190rpm 90 kg-cm Torque – WGM775127500-40K
- Product Name: Worm Gear Motor
- Rated Voltage: DC 12V
- No-load Speed: 15RPM
- Rated Speed: 190RPM
- Rated Current: 15A
- Rated Torque: 90KG.cm
- Output Power: 90W
- Reduce Ratio: 1:80
- Shaft Bore Diameter: 14mm
- Dimension:255*96*115 mm
- Commutation: Brush
- Reversible: Yes
- Lifespan: more than 2000 hours
- Net Weight: 3.98KG
Worm Gear Box Reduction Motor 12V 94rpm 90 kg-cm Torque – WGM775127500-80K
Worm Gear Box Reduction Motor 12V 11rpm 150 kg-cm Torque – WGM775126000-548K
- Product Name: Worm Gear Motor
- Rated Voltage: DC 12V
- No-load Speed: 15RPM
- Rated Speed: 11RPM
- Rated Current: 15A
- Rated Torque: 150KG.cm
- Output Power: 90W
- Reduce Ratio: 1:80
- Shaft Bore Diameter: 14mm
- Dimension:255*96*115 mm
- Commutation: Brush
- Reversible: Yes
- Lifespan: more than 2000 hours
- Net Weight: 3.98KG
TowerPro MG996R 360 Deg Rotation Digital High Torque Servo Motor
- Gear Type: Metal gear
- Servo Plug: JR (Fits JR and Futaba)
- Weight: 55g
- Dimension: 40.7×19.7×42.9mm
- Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v)
- Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v)
- Operating voltage: 4.8 ~ 6.6V
- Gear Type: Metal gear
- Dead band width: 1us
- Wire length: 32cm
- Servo arms & screws included, and fit with Futaba servo arm
- It’s universal “S” type connector that fits most receivers, including Futaba, JR, Hitec ,GWS, Cirrus, Blue Bird, Blue Arrow, Corona, Berg, Spektrum.
- CE & RoHS approved
L293D Motor Driver Board for ESP8266 WiFi NodeMcu Lua ESP12E
- Motor power supply Range: 4.5V ~ 36V
- Control power Range: 4.5V ~ 9V (10VMAX)
- Logic Operating current: ≤60mA
- Drive part of the work current Io: ≤1.2A
- Maximum power dissipation: 4W
- Drive Type: Dual high-power H-bridge driver
- Working temperature: -25 ℃ ~ + 125 ℃
- ESP12 DEV KIT development board expansion module
- Lead ESP12 DEV KIT all the features of pins: SPI, UART, GPIO, AI, and 3.3V power connector
- Extend two-way motor-driven, two-way direct-drive motor
- on board power switch
- Motor power, control power separation
- Dimension: 60 x 45 x 13mm
6V 12V 24V 8A PWM DC Motor Speed Controller CCM5D Digital Display LED Motor Controller Speed Regulator
- Input Supply Voltage: 6V-30VDC
- Continuous Current (A): Rated current 5A (8A MAX, cannot be prolonged)
- Maximum Output Power: 240W
- LED display the duty ratio: 0-100%
- PWM Frequency: 16khz
- Duty Cycle adjustable: 0%-100%
- Dimensions: 78*42*25mm
- The display range of 3-digit LED display is "000"-"100".
- Adjustable speed range is 0%-100%
- Fine workmanship and good performance.
- Easy to use.
- Long service life.
- Suitable for the DC motor (or DC load) within 5A, Peak current 8A.
- Incorporate a push key. Push closed, and then push open
Worm Gear Box Reduction Motor 12V 350rpm 22 kg-cm Torque – WGM5551212000-34K
Worm Gear Box Reduction Motor 12V 110rpm 30 kg-cm Torque – WGM555127500-68K
- Operating Voltage: 12.V DC
- Rated Current: 1.1 A
- Rated Base Motor RPM: 7500.
- Rated Speed: 110RPM
- Rated Torque: 30kg-cm
- Operating Temperature: (°C) - -40 °C ～ +100°C.
- Relative Humidity(RH): 20% ～ 85% .
- Housing Material: Metal.
- Shaft Type: D-type.
- Motor Height: 27mm
- Motor Width: 40mm.
- Motor Length: 115mm
- Shaft Diameter: 8mm
- Shaft Length: 15mm
- Shaft Type: D-type. Motor