CJMCU-34725 TCS34725 Color Sensor RGB Module
- Operating Voltage: 3.3V
- Supply Voltage: 3.3V-5V
- Color management is more accurate
- High sensitivity
- Wide dynamic range
- IR shading filters make the TCS34725 ideal
- Integrated IR blocking filter
- 8M:1 dynamic range
- Four independent analogue-to-digital converters
- A reference channel for colour analysis (clear channel photodiode)
- Length: 20mm
- Width: 20mm
- Weight: 10 g
Color Sensor
- Voltage supply: 2.7V to 5.5V
- Colour sensor IC: TSC3200
- Interface: digital TTL
- Single-Supply Operation (2.7V to 5.5V)
- High-Resolution Conversion of Light Intensity to Frequency
- Programmable Color and Full-Scale Output Frequency
- Power Down Feature
- Programmable colour and full-scale output frequency.
- Easy to interface with microcontrollers like AVR, ARM, PIC, Arduino etc
- S0~S1: Output frequency scaling selection inputs
- S2~S3: Photodiode type selection inputs
- OUT Pin: Output frequency
- OE Pin: Output frequency enable pin (active low), can be impending when using
- Support LED lamp light supplement control
- Working temperature range: -40℃ to +80℃
Current Sensor ACS712 20AMPS
- Supply Voltage: 4.5V ~ 5.5V DC
- Measure Current Range: 20A
- Sensitivity: 100mV/A
- The low-noise analogue signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8
- Small footprint, low-profile SOIC8 package
- 1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8
- Output voltage proportional to AC or DC currents
- Factory-trimmed for accuracy
- Extremely stable output offset voltage
- Nearly zero magnetic hysteresis
- The ratiometric output from the supply voltage.
CURRENT SENSOR ACS712 30AMPS
- Current sensor chip: ACS712ELC-30A
- Supply voltage: 4.5V to 5.5V DC
- Current range: -30A to 30A
- Sensitivity: 66 millivolt/ampere
- Low noise analogue signal path
- Output rise time: 5 micro sec
- Extremely stable output offset voltage
- Zero magnetic hysteresis
- Factory trimmed for accuracy
- Easy to interface with a microcontroller, since it outputs an analogue voltage
- Onboard power indicator
- Dimension: 7*5*5cm
- Weight: 400gm
Current Sensor ACS712 5AMPS
- Supply Voltage: 4.5V ~ 5.5V DC
- Measure Current Range: -5A ~ 5A
- Sensitivity: 100mV/A
- Low-noise analogue signal path.
- Device bandwidth is set via the new FILTER pin.
- 5 µs output rise time in response to step input current.
- Small footprint, low-profile SOIC8 package.
- 1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
- 0 V, single-supply operation.
- 66 to 185 mV/A output sensitivity.
- Output voltage proportional to AC or DC currents.
- Factory-trimmed for accuracy.
- Extremely stable output offset voltage.
- Nearly zero magnetic hystereses.
- The ratiometric output from the supply voltage.
- Dimension: 31*13mm
DB9 BreakOut Board
DB9 Female screw Terminal to RS232 RS485 Conversion Board
- Perfect for experimentation and prototype work
- Brings all 9 pins of a DB9 connector to screw terminal blocks
- Adapter used for communication debug
- 9 pcs signal line was all lead out, name and number clearly labelled
- All-copper DR9 seat, anti-oxidation, better contact
- Military board, three anti-paint sprays an entire board, corrosion-resistant
- Terminal spacing 3.96MM, screw hole diameter 2MM, need to use a width of 2MM screwdriver for assembly
- Use of environmentally friendly copper terminals, through IS0-9001.
DC POWER SUPPLY MODULE FOR DC ADAPTER PLATE
DC-DC BOOST MODULE 0.9V-5V/5V 600MA USB MOBILE Power Supply Module
- Ultra-compact PFM chip
- Module properties: nonisolated step-up module
- Input voltage: 1v-5v
- Output voltage: 5.1v-5.2V
- Output current: rated 1A-1.5A
- Efficiency: 96%
- Output ripple: 30mv for 20M bandwidth
- Switching frequency: 500khz
- Voltage indication for led lights with load( for less than 2.7v led indicator off)
- Operating temperature:-40 degrees to 85 degrees Celsius
- Full load temperature rise: 30 degrees Celsius
- Quiescent current: 130ua
- Load regulation: +/-1%
- Voltage regulation: +/-0.5%
- Dynamic response speed: 5% 200Us
- Short circuit protection
- Reverse polarity protection
- Dimension: 2.5*1.8*1.8gm
- Weight: 400gm
DC-DC Booster Module 3v-20000v
- Input voltage: DC 3V Input Current: 1.5A
- Output voltage: DC20KV
- Output current: 0.05AÂ
- Input Line Length: approx. 110 mm (red is positive)Â
- Output cable length: approx. 110mm
- High voltage bipolar discharge distance: 5mmÂ
- type: pulse currentÂ
- Structure: and low voltage integrated
- Material: metalÂ
- Color: black and black
- High-Quality Silicone Wires at Input and Output
- Small in Size
- Easy to Use
- Size: 19 x 20 x 18 mmÂ
Delay Timer Switch Adjustable 0-10sec With NE555 Electrical Input 12V 10A
- Module based on the NE555 chip.
- Input voltage: DC 12V
- Adjustable time: 0-10 s
- AC Control voltage: 250V/max. 10A
- DC Control Voltage: 30V/max. 10A
- load: 2200W
- Precision Pulse Generation / Timing.
- Monostable Operation.
- Standby no power consumption
- Excellent temperature stability of 0.005%/°
- Time can be adjusted by a potentiometer, the default is 0-25 seconds
DHT11 MODULE
- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: 0°C to 50°C
- Humidity Range: 20% to 90%
- Resolution: Temperature and Humidity both are 16-bit
- Accuracy: ±1°C and ±1%
- Low power consumption.
- The module can detect the surrounding environment of the humidity and temperature
- High reliability and excellent long-term stability
- The output from the digital output
- Has fixed bolt hole and easy installation