AC-DC Power Module HLK-PM12 230V to 12V /3W
- Rated input voltage: AC 100V -230V
- Input voltage range: 90V -264V AC
- Maximum input current: <0.2A
- Input current surge: <10A
- Maximum input voltage: <270V AC
- Input Low Voltage Efficiency Vin=110V AC，Output full-load≥ 69%
- Input High Voltage Efficiency Vin=220V AC，output full-load≥ 70 %
- Short-term maximum output current: ≥1000 mA
- Long-term reliability
- Voltage Regulation: ±0.2%
- Load Regulation: ±0.5%
- Ultra-thin and small module
- High efficiency, high power density
- Low ripple and low noise
- Output overload and short circuit protection
- Working temperature: – 20 degrees to +60 degrees Celsius
- Storage temperature: -40 degrees to 80 degrees Celsius
- Relative humidity: 5-95%
- Cooling way: Natural cooling
- Atmospheric pressure: 80-106Kpa
- Weight: 21g
- Size: 38x23x18mm
ACTIVE BUZZER ALARM
- Operating voltage: 3.3V to 5V
- The Transistor driver module uses S8550/9012
- Wire length: 20.5cm
- Easy installation by the fixed bolt hole
- 3 pin TTL cable
- An active buzzer with a concussion internal source is called to be energized
- The program easy to control-SCM high low sound
- When input I/O input is low level, the buzzer sounds
- 28*13.29*11.5mm
AD620 Microvolt/Millivolt Voltage Amplifier Module
Adapter Breakout PCB for ESP 32F ESP32 ESP-WROOM-32 Wireless Bluetooth Module
ADS1115
ADXL345
- Supply voltage: 3.3V/5V
- Communication type: I2C/SPI
- Sensing range: +/-2G to +/-16G
- Sensitivity
- X: 28.6 LSB/G
- Y: 31.2 LSB/G
- Z:34.5 LSB/g
- On-board LDO voltage regulator
- Resolution: 13 bit
- Single tap/double-tap detection
- Embedded memory management system with FIFO
- 10000g shock survival
- Low power consumption as low as 23 µA in measurement mode and 0.1 µA in standby mode at VS = 2.5 V (typical)
- 3-axis MEMS accelerometer
- Ideal for noisy power environment
- Operating temperature: -40 degrees to 85 degrees Celsius
- Dimension: 28*14mm
AM2302 WIRED MODULE
- Low cost
- 3V to 5V power and I/O
- 5mA max current use during conversion (while requesting data)
- Good for 0-100% humidity readings with 2-5% accuracy
- Good for -40 to 80°C temperature readings ±0.5°C accuracy
- No more than 0.5 Hz sampling rate (once every 2 seconds)
- 3 wires 23cm long (9")
- Dimensions: 27x 58.75 x 13.30mm
AMS1117 3.3V POWER SUPPLY MODULE
• Input: DC 4.5V – 12V (input voltage must be more than the output voltage (more than 1V))
• Output: 3.3V, 800mA (load current cannot exceed 800mA)
• Onboard AMS1117 chip.
• Onboard power indicator to indicate power is turned on: Red LED.
• Output voltage interface, connection to facilitate the experimental.
• Specially designed two pin mounting holes, can be directly fixed on the whole expansion board for experiments.
• Small Compact Size, 4Pin Type, Breadboard Friendly.
• 2P single row pin input and output for easy connection
• Dual-panel design, the layout is nice
AMS1117 5V POWER SUPPLY MODULE
• Input: DC 6.5V – 12V (input voltage must be more than the output voltage (more than 1V))
• Output: 5V, 800mA (load current cannot exceed 800mA)
• Onboard AMS1117 chip.
• Onboard power indicator to indicate power is turned on: Red LED.
• Output voltage interface, connection to facilitate the experimental.
• Specially designed two pin mounting holes, can be directly fixed on the whole expansion board for experiments.
• Small Compact Size, 4Pin Type, Breadboard Friendly.
• 2P single row pin input and output for easy connection
• Dual-panel design, the layout is nice
Analog Hall Magnetic Sensor Module
- Operating Voltage: 3.3V-5V
- Wide range voltage comparator LM393
- Number of Pins: 4.
- Sensitivity is Adjustable.
- Output form digital switch output (0 and 1 high and low level)
- The output effective signal is a low level
- Signal output indicator with the retaining bolt hole, convenient installation
- When there is sound, outputs low level and the signal light
- Single-channel signal output
- Can be used for Acoustic control light, give sound and light alarm working with the Photosensitive sensor, and sound control, sound detect
APDS-9930 Gesture Sensor Digital Proximity And Ambient Light Sensor For Arduino
- Working voltage:2.8-3.8V
- ALS, IR LED, and Proximity Detector in an Optical Module
- Approximates Human Eye Response
- Programmable Interrupt Function with Upper and Lower Threshold
- Programmable range from 2.7 ms to more than 8 seconds
- Up to 16-Bit Resolution
- High Sensitivity Operates Behind Darkened Glass
- Low Lux Performance at 0.01 lux;
- Ambient Light Sensing (ALS)
- Proximity detection
- I2C interface is compatible up to 400kHz (I2C fast mode) –