- You cannot add "6V 12V 24V 8A PWM DC Motor Speed Controller CCM5D Digital Display LED Motor Controller Speed Regulator" to the cart because the product is out of stock.
20A PWM Motor Speed Controller DC 6 30V 6V 12V 24V 48V
40A DC MOTOR SPEED REGULATOR PWM CONTROLLER 2000W
- Speed controller model: 40A PWM DC motor speed regulator
- Operating voltage: 10V TO 50V
- Peak current: 40A
- Control power: 0.01-2000W
- Quiescent current: 0.025A
- PWM regulation: 5-100%
- PWM frequency: 12KHz
- Operating temperature: -20 degree to 40 degree Celsius
- Stability in working
- High efficiency
- potentiometer used for speed adjustability
- Dimension: 9*5.1mm
- Weight: 95gm
6V 12V 24V 8A PWM DC Motor Speed Controller CCM5D Digital Display LED Motor Controller Speed Regulator
- Input Supply Voltage: 6V-30VDC
- Continuous Current (A): Rated current 5A (8A MAX, cannot be prolonged)
- Maximum Output Power: 240W
- LED display the duty ratio: 0-100%
- PWM Frequency: 16khz
- Duty Cycle adjustable: 0%-100%
- Dimensions: 78*42*25mm
- The display range of 3-digit LED display is "000"-"100".
- Adjustable speed range is 0%-100%
- Fine workmanship and good performance.
- Easy to use.
- Long service life.
- Suitable for the DC motor (or DC load) within 5A, Peak current 8A.
- Incorporate a push key. Push closed, and then push open
A3967 STEPPER MOTOR DRIVER
- A3967 precision micro-stepping driver
- Power supply: 7v to 30v
- Logic voltage: 5v to 3.3v
- Higher the voltage higher the torque at high speed
- Adjustable current control from 150Ma/ phase to 750ma phase
- Automatic current decay mode detection/selection
- Fast, slow, and mixed current decay modes
- Internal UVLO and thermal shutdown circuitry
- Crossover current protection
- Micro stepping resolution to full, half, quarter, and eighth steps by broken out MS1 and MS2 pins.
- Compatible with Arduino, GRBL G-Code interpreter for driving3-axis CNC machines
- Salington sink drivers used
- Compactible with 4, 6,8 wire stepper motor of any voltage
A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
BTS7960 43A High Power Motor Driver Module/Smart Car Driver Module for Arduino Current Limit
- Input voltage: 6V-27V
- Maximum current: 43A
- Input level: 3.3-5V
- Control mode: PWM or level
- Duty cycle: 0-100%
- Double BTS7960 large current (43 A) H bridge driver
- 5V isolate with MCU and effectively protect MCU
- 5V power indicator on board
- Four lines from MCU to driver module (GND. 5V. PWM1. PWM2)
- Reverse the motor forward, two PWM input frequency up to 25kHZ
- Two heat flow passing through an error signal output
- Dimension: Approx. 4 * 5 * 1.2cm