I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
-2%
150mm 6 inch LCD Digital Electronic Vernier Caliper
Original price was: ₹900.00.₹850.00Current price is: ₹850.00. inc. GST
Protosheild For Arduino
Original price was: ₹355.00.₹250.00Current price is: ₹250.00. inc. GST
RELAY SHEILD
Original price was: ₹510.00.₹499.00Current price is: ₹499.00. inc. GST
- Every channel maximum convert voltage: AC 125V / DC 24V
- Every channel maximum converts current: 3A
- Interface via digital I/O pins 4,5,6, and 7
- Relay screw terminals
- Standardized shield shape and design
- LED working status indicators for each relay
- High quality relays
- COM, NO (Normally Open), and NC (Normally Closed) relay pins for each relay
- Update pin SCL, SDA, IOREF, NC.
- Arduino,Crowduino,Seeeduino,Arduino Mega compatible
- Automatic control and manual control
- 4 mechanical relays with photo-coupled circuit
- 3-M3 screw hole easy to install
- Driven by 5V / 3.3V normally open contact close
Description
The Relay Shield is designed as an Arduino compatible smart module with 4 mechanical relays. This is a simpler and easier way to control high voltage with maximum switching power of 35VDC 70W for each channel. This Relay Shield module is controlled directly by Arduino/Crowduino through digital IOs with an external 6.5 to 12V DC supply. The 4 onboard control keys used to control the high voltage without programming. It features four high-quality relays and provides NO/NC interfaces. And four dynamic LED indicators to show the on/off state of each relay. And the standardized shield form factor to provide a smooth connection to the Arduino/Seeeduino board or other Arduino compatible boards.
The Relays are basically electromagnetic switches in which the relay is energized by the control circuit. When a voltage and current are applied to the coil, the current and coil create a magnetic field. As a result, it attracts the COM terminal towards the NO terminal. When the applied voltage and current are removed from the control circuit, the COM terminal returns to contact the NC terminal due to a mechanical force (usually a spring). The two “Control Circuit” terminals for each of four relays are controlled by only one Arduino Digital I/O pin. The Pins 4, 5, 6, and 7 control relays 4, 3, 2, and 1 respectively. These relay shields are used to control high voltage using low voltage, motor control, remote control, anti-hearing alarm, automatic temperature alarm, incubators, and so on.
Note: The pins on the Shield should not touch the USB connector of Arduino UNO when they are connected.
J1 Interface/Terminal Pin Description:
- COM1 (Common Pin): The relay pin is controlled from the digital pin.
- NC1 (Normally Closed): This terminal is connected to COM1 when the RELAY1 control pin (Digital 7 I/O pin) is set to low and disconnected when the RELAY1 control pin set to high.
- NO1 (Normally Open): This terminal connected to COM1 when the RELAY1 control pin (Digital 7 I/O pin)set to high and disconnected when the RELAY1 control pin set to low.
Terminals J2-4 are similar to J1 except that they control RELAY2-RELAY4 respectively.
Reviews (0)
Shipping & Delivery
Related products
2.4″ Inch Touch Screen TFT Display Shield for Arduino
- 4″ Touch LCD TFT display module for Arduino
- 240*320 pixels resolution
- Ability to display 262000 different colours
- The shield comes equipped with a microSD card slot.
- SPFD5408 controller with built-in video RAM buffer
- 8-bit digital interface, plus 4 control lines
- 5V compatible. Use with 3.3V or 5V logic
- On-board 3.3V 300mA LDO regulator
- Uses digital pins 5-13 and analogue 0-3. That means you can use digital pins 2, 3, and analog 4 and 5. Pin 12 is available if not using the microSD
- Works with any Arduino Uno and mega compatible boards
- Resolution: 240320 pixels
- Supply voltage: 5V
- Working temperature: -30C ~ 70C
- Dimension: 72*52*12mm
DTMF Shield
- MT8870 Decoder IC.
- 4 Output digital pins.
- Operates on 5V
- Includes MT8870 DTMF Receiver IC
- Receives and Converts Standard DTMF Codes
- Remotely Switch Devices from Anywhere Using the Phone
- Easily Connects to Most Microcontrollers or Roboduino Board
- Low Power Consumption
- 5 On-Board LED's For Data Received Indication
- Standard Header Connections for Control System Connection
- Audio socket for application
- Speaker connector for audio sound checking.
- Microphone connector for over the air remote control system( note, due to environmental noise, without any filtering system this method is not recommended)
- Dimension: 37x37x9mm
Dual Monster Moto Shield VNH2SP30 Motor Driver 2x14A (Peak 30A)
- Driver Model: VNH3ASP30
- Current sensing available to Arduino analogue pin
- Operating Voltage: 12 V to 16V DC
- Peak Current: 14A
- Continuous Current: 30A
- of Channels: 2
- Maximum PWM frequency: 20 kHz
- MOSFET on-resistance: 19 m (per leg)
- Thermal Shutdown protection
- Under-voltage and Overvoltage shutdown.
- LED Indicator
- Dimensions: 60 x 54 x 12mm
- Weight: 19gm
Ethernet Shield
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560).
- Can be accessed using the Mini SD TF library.
- The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted-pair Category 5 Ethernet cable.
- IEEE802.3af compliant
- Low output ripple and noise (100mVpp)
- Overload and short-circuit protection
- 1500V isolation (input to output)
HC-05 Bluetooth Shield for Arduino
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Communication Range: 10M
- Serial Bluetooth module for Arduino
- Can operate in Master, Slave or Master/Slave mode
- UART interface (TTL) with programmable baud rate (SPP firmware installed)
- Default baud rate: 38400(CMD MODE) / 9600(DATA MODE), data bits: 8, stop bit: 1, Parity: No parity
- Onboard PCB antenna
- FCC ID certificated
MEGA Sensor Shield V2.0
- PIN13 Stat & Power LED indicator
- Digital IO Ports D0-D53
- Analog IO Ports A0-A15
- Reset Button up to the top
- External Power In
- SD Card Interface
- Ultrasonic Interface
- ISP Interface
- Bluetooth Interface
- APC220 Interface
- PCB finest Immersion Gold processing
- Plug it easier to set up a variety of commonly used module interface
PN532 NFC/RFID Controller Shield for Arduino
- PN532 chip-set
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI
- I2C: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance:10cm
- Easy to change mode
- NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna
- 36-pin 0.1" header for attaching the shield to an Arduino.
- Compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
SIM800A Quadband GSM / GPRS Module convertible as Shield for Arduino
- Quad-Band GSM/GPRS 850/ 900/ 1800/ 1900 MHz.
- GPRS class 2/10.
- Input Voltage: 9V-12V DC.
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
- Configurable baud rate.
- Built-in SIM Cardholder.
- Built-in Network Status LED.
- 5V interface for direct communication with MCU kit.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Low power.
- SMA connector with GSM L Type Antenna.
- Headphone jack for audio out.
- Li-Po battery 3.7-volt pins for supply.
- Li-Po battery USB charger (3.7volts).
- CP2102 port for communication with a laptop.
Reviews
There are no reviews yet.