HDMI Male to VGA Female Converter Adapter 1080P For PC, Rspberry Pi
- Support HD resolution, super clear picture, fast transmission speed
- The maximum signal range up to 1920 X 1200, 1080p;
- Video input signal: 5Volts p-p(TTL) ;
- Support VGA video bandwidth: 10 bit, 162MHz
- Video amplifier bandwidth: 162MHz
- Support resolution up to 1920 X 1200, reduce blank signal during transmit.
- No external power supply, plug, and play.
A-Male to A-Female USB 2.0 Extension Cable (150cm)
- Hi-Speed 480 mbps With 3g Dongle Support.
- Easy to operate, bring you great convenience.
- Made of high-quality Material
- USB 2.0 A Male to A Female Extension Cable.
- A-male to A-female USB cables are typically used to extend the reach of your existing USB A/B cable, or to use USB device such as memory stick on your desk instead of inserting it to the back of PC
- Left connector type: USB 2.0.
- Left connector gender: Male.
- Right connector type: USB 2.0.
- Right connector gender: Female
SIM Card Holder
LM 2576HV Buck Module
- Module Properties: non-isolated constant voltage module
- Rectification: non-synchronous rectification
- Input voltage: 4.5V-60V
- Output Voltage(Less than input): 1.3V-26V
- Continuous operating current: 1.2A (output total power within 20W)
- Output current: 3A maximum
- Conversion efficiency: 92% (maximum)
- Switching frequency: 52KHz
- Output ripple: 50mV (maximum) 20M-bandwidth
- Load regulation: ± 0.5%
- Voltage regulation: ± 2.5%
- Operating temperature: -40 ℃ to +85 ℃
- Size: 43 * 30 * 14 mm
LM2577 Boost power module
- Input voltage range : 3-34V DC
- Output voltage range : 4-35v DC adjustable
- Output current:3A
- Voltmeter range:0 to 40V,error +-0.1v
- Multiple output regulator.
- One button to switch input and output voltage display.
- Power-down memory function.
- Press the button for 3 seconds can turn OFF/ON the LED display.
- Multiple output regulator.
- When adjusting the blue potentiometer, please use a multimeter to monitor the voltage
- Rotating Clockwise can raise the voltage while rotating counter clockwise could lower the voltage
Screw Shield Expansion board for Arduino
- Arduino terminal to provide the IO, port connection.
- 81 posts quality, reliable, convenient, durable.
- Combined with the Proto Shield, the middle can be used as a prototype expansion board.
- Double-sided PCB Prototyping extended area vias connecting the front sides can be welded components.
- The middle section can be placed small bread plate, convenient test extend
DTMF Shield
- MT8870 Decoder IC.
- 4 Output digital pins.
- Operates on 5V
- Includes MT8870 DTMF Receiver IC
- Receives and Converts Standard DTMF Codes
- Remotely Switch Devices from Anywhere Using the Phone
- Easily Connects to Most Microcontrollers or Roboduino Board
- Low Power Consumption
- 5 On-Board LED's For Data Received Indication
- Standard Header Connections for Control System Connection
- Audio socket for application
- Speaker connector for audio sound checking.
- Microphone connector for over the air remote control system( note, due to environmental noise, without any filtering system this method is not recommended)
- Dimension: 37x37x9mm
USB Host Shield
- Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
- Operates over the extended -40°C to +85°C temperature range
- Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
- Supports HID devices, such as keyboards, mice, joysticks, etc.
- Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard drives (FAT32 Type File System – Mega Arduino only).
Bluetooth Relay Shield
CAN Bus Shield
- Implements CAN V2.0B at up to 1 Mb/s
- Industrial standard 9 pin sub-D connector
- OBD-II and CAN standard pinout selectable.
- Changeable chip select pin
- Changeable CS pin for TF card slot
- Changeable INT pin
- Screw terminal that easily to connect CAN_H and CAN_L
- Arduino Uno pin headers
- Grove connectors (I2C and UART)
- SPI Interface up to 10 MHz
- Standard (11 bit) and extended (29 bit) data and remote frames
- Two receive buffers with prioritized message storage
Joystick Shield
SD Card shield V4.0 for Arduino UNO
- Standard SD card, SDHC card and TF card compatible
- 3.3v and 5v logical voltage compatible
- 2.6-3.6v DC power supply
- UART Grove & I2C connection compatible
- Fully supported SD Library
- Minimal number of SPI port
- Jumpers provided for configuring Arduino SPI port pins
- Onboard toggle switch for SD card select type
- Truly stackable
- Prototype expand Library support
- Size: 53mm x 47mm
- Weight: 35g