Sonar Range Finder -High Performance Ultrasonic Sensor Module
- Low-cost ultrasonic rangefinder
- Size less than 1 cubic inch with easy mounting
- Resolution of 1mm
- 100mS measurement cycle
- The free run operation uses a 2Hz filter, with 100mS measurement and output cycle
- Operating temperature range from -15°C to +65°C
- Operating voltage from 2.5V to 5.5V
- Nominal current draw of 2.5mA at 3.3V, and 3.1mA at 5V
50~100 DC12V W1209 Digital Thermostat Thermometer Temperature Control
- Supply Voltage: 12V
- Measuring Inputs: NTC10K
- Measurement Accuracy: 0.1 C
- Control Accuracy: 0.1 C
- Refresh Rate: 0.5 Seconds
- Cable Length: 0.5 Meter
- Output Type: 1 Channel Relay Output
- Capacity: 10A
- Temperature Control Range: -50 ~ 110 C
- Resolution at -9.9 to 99.9: 0.1 C
- Resolution at all other temperatures: 1 C
- Temperature: -10 ~ 60 C
- Humidity: 20-85%
- Dimensions:48mm x 40mm x 14mm
SWIVEL INFRARED MOTION SENSOR OCCUPANCY SWITCH
- Power frequency: 50~60Hz
- Control light: <3 LUX ~ 2000 Lux (Adjustable)
- Time-Delay: Minimum:8sec±3sec to a Maximum:7min±2min
- Power source: 100V/AC-130V/AC <=> 220V/AC-240V/AC
- 1200W(220V/AC-240V/AC) - 800W(100V/AC-130V/AC)
- Power consumption:0.45W(static 0.1W)
- Detection range: 180°
- Detection distance: 12 meters maximum at less than 24°C
- Working temperature:-20 to 40°C
- Working humidity: Less than 93% Relative Humidity
- Suggested Installation height: 0.5 meter to 3.5 meters
- Detection motion speed: 0.6 to 1.5 meters per second
- Identify day and night automatically -
- Power and detection indication
- Time-delay added continually
- Time-delay adjustment according to the customer desire. The minimum time is 8sec±3sec and the maximum is 7min±2min.
- Locking function: the sensor will keep load lighting when power is shut off for 2 seconds and then on. When power is shut off for 4 seconds and then on, sensor will resume automation.
SHARP Air detection sensor dust sensor GP2Y1010AU0F KG017
- Operating Voltage: 4.5V to 5.5V
- Low Current Consumption: 20mA max
- Sensitivity: 0.5V/(0.1mg/m3)
- Clean-air voltage: 0.9V typical
- Storage temperature:-20 ~80 degrees Celsius
- Minimum Detectable Dust Size: 0.5µm
- Smallest particles detected value: 0.8 micron
- Dust Density Sensing Range: Up to 580 µg/m3
- Sensing Time: Less than 1 Second
- Service life: 5 years
- The presence of dust can be detected by the photometry of only one pulse
- Enable to distinguish smoke from house dust
- Lead-free and RoHS directive compliant
- Operating temperature:-10 -65 degrees Celsius
- Dimensions: 46.0 x 30.0 x 17.6 mm
- Weight: 15gm
36V/48V/60V Lithium battery case 400*165*90mm ABS Plastic material
- Dimensions: 400*165*90mm.
- Suitable for battery type: 36/48/60V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V.
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
36V/48V/60V Lithium battery case 360*160*100MM APS Plastic Material
- Dimensions: 360*160*100mm.
- Suitable for battery type: 36/48/60V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V.
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
36V/48V Fold bike Lithium Battery Case 410*100*42mm Aluminum Alloy Material
- Dimensions: 410*100*42mm.
- Suitable for battery type: 36/48V.
- Battery standard: 18650 lithium battery.
- Charging voltage: 42V/54.6V
- Used to install an electric vehicle lithium battery.
- Suitable for electric bicycles, electric bicycles, and folding electric vehicles.
- Made up of aluminium alloy and plastic, which is sturdy and durable.
- The product has a charging socket and an output port.
HC-05 Bluetooth Shield for Arduino
- Bluetooth serial port Profile
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Communication Range: 10M
- Serial Bluetooth module for Arduino
- Can operate in Master, Slave or Master/Slave mode
- UART interface (TTL) with programmable baud rate (SPP firmware installed)
- Default baud rate: 38400(CMD MODE) / 9600(DATA MODE), data bits: 8, stop bit: 1, Parity: No parity
- Onboard PCB antenna
- FCC ID certificated
ESP8266 WIFI Shield
- Operating voltage 5V (supplied from the Arduino Board)
- Connection via: 802.11b/g networks
- Encryption types: WEP and WPA2 Personal
- Connection with Arduino on SPI port
- on-board micro SD slot
- ICSP headers
- FTDI connection for serial debugging of WiFi shield
- Mini-USB for updating WiFi shield firmware
- 32-bit RISC architecture
- The processor can operate at 80MHz / 160MHz
- 32MB flash memory
- 64kB for instructions
- 96kB for data
- Operates in AP, Station or AP + Station mode
- It has 11 digital pins
- It has 1 analogue pin with 10-bit resolution
- Digital pins except the D0 have interrupts, PWM, I2C and one wire
- Programmable through USB or WiFi (OTA)
- Compatible with Arduino IDE
- Compatible with modules and sensors used in Arduino
PN532 NFC/RFID Controller Shield for Arduino
- PN532 chip-set
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI
- I2C: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance:10cm
- Easy to change mode
- NFC/RFID PN532 shield including a tuned 13.56MHz stripline antenna
- 36-pin 0.1" header for attaching the shield to an Arduino.
- Compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
16×2 (1602) LCD Keypad Shield
- Operating Voltage:5V
- 5 Push buttons.
- RST button to reset Arduino program.
- Integrate a potentiometer for adjusting the backlight.
- Expanded available I/O pins.
- Blue light with white characters.
- Uses 4 Bit Arduino LCD Library
- Screen contrast adjustment
- Arduino Reset button
- The keypad consists of 6 keys select, up, right, down, left and reset.
- To save the digital IO pins, the keypad interface only uses one ADC channel.
- The key value is read out through a 5 stage voltage divider.
Protosheild For Arduino
- Standard 0.1"x0.1" prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- Reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
- A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
- A surface-mount chip area for up to 14 SOIC size parts
- Compatible with tiny breadboards
- Every pin is brought out
- Gold plated pads
- 2 x 0.1uF capacitors on either side for extra power stability