Ina219 I2C BiDirectional DC Current Power Supply Sensor Breakout Module
- 1 ohm 1% 2W current sense resistor
- Up to +26V target voltage
- Up to ±3.2A current measurement, with ±0.8mA resolution
- Senses Bus Voltages from 0 to 26 V
- I2C- or SMBus-compatible interface. The
- Reports Current, Voltage, and Power
- 16 Programmable Addresses
- Filtering Options
- Calibration Registers
- SOT23-8 and SOIC-8 Packages
- Using a single power supply, the working voltage is between + 3.0 to + 5.5 V.
- Calibration programmable registers directly read its unit of measure in the ampere current, and power in watts per reading.
- For as many as 128 samplings averaging, in order to realize filter in the noise environment.
- The I2C interface timeout, not only avoid the bus lock but also can provide high-speed mode, meet the communication requirements of up to 3.4 MHz.
- Supported software programmable INA219.
- Dimensions: 0.9*0.8inch
- Weight: 1.9g
Infrared Ir Obstacle Avoidance Detector Sensor Module Adjustable 2-180cm
- Power requirements: 5 VDC
- Communication: Digital High/Low Output
- A variety of welding methods, vertical and horizontal, to expand the scope of application
- Add precision potentiometer to adjust infrared 38KHz detection range
- Sensor detection with enabling the port, convenient signal line as bus application line
- Power-on enable port default level, the sensor enables the detection output signal
- Detection range up to 1.2 meters
- Software enhancement, setting can avoid infrared light interference of the same module or other kinds of infrared remote control devices
- Working condition of each module recorded with EEPROM, reduce the probability of mutual interference of the same paragraph to 1%
- Signal low output
- Pin SIP header, applied in breadboard or through-hole project
- On-board set jumper JP, the signal output has a latch function when shorted, otherwise, it is jog output
- Operating temperature: 32 to 158 ° F (0 to +70 ° C)
- Size: 2.4cm × 2.8cm
IR Infrared Obstacle (Imported)
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
IR Proximity Module using TSOP
- Operating wavelength: Near-infrared region 700 nm to 1400 nm
- Main Chip: LM358
- Operating Voltage Range: 3.6V-5V DC
- Average Current Consumption: 06mA
- Distance Measuring Range: 2 to 30cm
- Detection angle: 35 °
- Easy to assemble and use
- On-board detection indication
- the effective distance range of 2cm to 80cm
- A pre-set knob to fine-tune distance range
- If there is an obstacle, the indicator lights on the circuit board
- 3mm screw holes for easy mounting
- Dimensions: 48 x 14 x 8mm
- Weight:5gm
IR Sensor Array of 8
- 8 IR Sensors with High Range
- Operating voltage: 3.3 to 5V
- Current supply: 100mA
- Output format: 8 digital I/O compatible signal
- Optimal sensing distance: 3 mm.
- Maximum recommended sensing distance: 6 mm
- Distance between each IR Sensor: 15mm
- Analog and Digital Output pins
- Potentiometer to adjust the sensitivity of the individual sensors
- Applications Line Follower Robots Object Array Sensing
- No analogue to digital conversion requires
- Improved sensitivity over voltage-divider analogue output
- Parallel reading of multiple sensors is possible
- Quality FR4 grade PCB for best performance.
- Dimension: 74.93mm x 12.7mm x 3.175mm
IR-08H Infrared Obstacle Avoidance Sensor Module
- Infra-Red IR Emission Receiver IR-08H for Arduino
- Onboard with HS0038B HS38B IR receiver
- Operating Voltage: 3V – 5.5V
- Detection range : 2cm – 40cm
- Output level: Low logic level when an obstacle is detected
- Working current: 20mAh
- Working temperature: -10’C~+50’C
- IO interface: 4 line (-/+/S/EN)
- Output signal: TTL Level
- Adjusting mode: Multi resistance regulation
- Effective angle: 35°
- Size: 4.5 * 1.1cm(approx)
- Easy to assemble and use
- On-board detection indication
- Pin Connection to the board: 4 pins
- A pre-set knob to fine-tune distance range
IRF520 MOSFET DRIVER MODULE SENSOR
- Operating Voltage: 3.3v & 5v
- Digital level port
- Output load voltage: 0-24v
- Output load current: <5A
- The heat sink is added for currently more than 1A
- Compatible with Arduino, MCU, ARM, Raspberry pi
- PWM dimming LED used to step-less dimming, variable-speed motor
- Output PWM can be adjusted by the original IFR520 MOS
- Arduino can drive up to 24V, such as led lights, dc motors, miniature pumps, solenoid valves etc.
- Dimension:34*30*18mm
- Size: 10gm
ISD1760 MODULE (75 sec)
- On-board ISD1760 chip
- Operating voltage: 5v
- 75 sec of audio playback
- Onboard microphone for direct recording
- Frequency: 6KHz or 8KHz
- Recording time: 6K/75 sec, 8K/60 sec
- Output all pin for chip control
- Easy interface with microcontrollers using 2.54mm spaced male pin headers
- High-quality natural voice reduction
- LED status indication
- Long recording time and multiple messages
- Simple operation and better voice quality
- Control not only by buttons but also by SPI from a microcontroller
- Recording, erase, play, FT, fast forward, reset volume buttons
- Dimension: 49*41.5mm
- Weight: 22gm
ISD1820 MODULE (10 SEC)
- Operating voltage: 2.6v to 5v
- Record and playback up to 10 sec
- Push-button and microcontroller controllable AGC circuit added tom increase audio playback volume
- Recording time: 8- 20 sec
- Built-in microphone
- On-chip 8-ohm speaker driver
- High quality, natural voice restored
- Available single-chip control audio recording control mode: the key to control or microcontroller, IO has drawn the line of control
- Can be used as propaganda module
- Auto power down mode
- Duration and sample rate can be extended to 20 sec by varying resistance
- Dimension: 43*34*11mm
JOYSTICK MODULE
JQ6500 Voice Sound Module 16Mbit Music MP3 Play MCU Serial Control Module UART SPI Flash
- Input voltage: Power supply is at 3.2V-5V, 4.2V Power supply is the best
- Rated current: 20ma
- Standard DIP16 package.
- 30 level adjustable volume, 10 adjustable EQ
- Working temperature: -40~70°C
- Humidity: 5%~95%
- Support sampling rate (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
- 24-bit DAC output,
- dynamic range support 90dB, SNR support 85dB
- Full support FAT16, FAT32 file system, the largest support 32G TF card, support 32G U disk, 64M bytes NOR FLASH
- A variety of control mode, parallel port control mode, serial port mode, AD button control mode
- The audio data sorted by folder, up to 100 folders, every folder can be assigned 1000 songs
- You can plug in SPI flash, connect the computer can display spi flash letter to update the content;
- Controlled through the microcontroller serial port to play the specified music;
- Can be interrupted: that is, in the process of playing, press the button will interrupt the current state to perform the new;
- MP3 file format: supports all bit rates 11172-3 and ISO13813-3 layer3 audio decoding
KA2284 Audio level Indicator
- Chip: KA2284.
- Wide operating supply voltage: 3.5V-16V
- `Level amplitude can be adjusted.
- AC/DC signal can be controlled through the jump line.
- High gain rectifying amplifier included(Gv=26dB)
- Low radiation noise when LED turns on
- Logarithmic indicator for 5-dot LED of bar type.
- Constant current output( 15mA)
- Minimum number of external parts required
- PCB board size: 29 x 21 mm