LJ12A3-4-Z/BY PNP DC6-36V 8 mm INDUCTIVE PROXIMITY SENSOR
- Output type: PNP NO
- Supply voltage: 6V-36V
- Current output: 300mA
- Response frequency: 0.5khz
- Detecting distance: 4mm
- Wire type: cylindrical DC 3 wire type
- Switch appearance type: cylinder type
- Operating temperature: -25 degrees to 55 degrees Celsius
- Detect object: iron
- Red led checks proximity status
- High repeated positioning accuracy
- High switching frequency
- Reverse power protection, short circuit protection, directly connecting with PLC
- anti-vibration, dust, water, and oil prevention
- Dimension: 5*3*3cm
- Weight: 400gm
LM35 SENSOR
- Calibrated Directly in Celsius (Centigrade)
- Operates from 4 V to 30 V
- Linear + 10-mV/°C Scale Factor
- ±0.5°C Ensured Accuracy (at 25°C)
- Can measure temperature ranging from -55°C to 150°C
- Less than 60-µA Current Drain
- Low Self-Heating, 0.08°C in Still Air
- Non-Linearity Only ±¼°C Typical
- Low-Impedance Output, 0.1 Ω for 1-mA Load.
- Drain current is less than 60uA
- The output voltage is directly proportional (Linear) to temperature (i.e.) there will be a rise of 10mV (0.01V) for every 1°C rise in temperature
- Suitable for Remote Applications
- Low-cost temperature sensor
- Available in TO-92, TO-220, TO-CAN, and SOIC package
LM358 100 Times Gain Amplification Module Operational Amplifier Module
- On-board LM358 Chip
- 100 times gain circuit design
- On-board LM358 chip
- On-board 10K adjustable resistor, could adjust amplifier times
- On-board power indicator lamp
- All pins lead, directly Input/output signals
- Working voltage: 5V-12V DC
- The chip has led major pin can be directly input and output signals.
- PCB size: 32.7mm x 13.3mm
Load Cell CZL 601 40KG
Load Cell CZL 601 80KG
- Type: Single Point Load Cell
- Total Precision: C3 class
- Material: Aluminum Alloy
- Surface: Anodized Treatment
- Protection: IP65
- Rated Load: 80 Kg. Max
- Rated Output : 2.0 mV/V+/- 5%
- Zero Balance : +/- 1% Full Scale
- Excitation Voltage: 9-12 Volt DC
- Nonlinearity : 0.017% Full Scale
- Hysteresis: 0.02% Full Scale
- Repeatability : 0.01% Full Scale
- Creep(30min) : 0.015% Full Scale
- Operating Temperature : -20 °C to +65 °C
- Safe Overload: 120% of Rated Capacity
- Ultimate Overload: 150% of Rated Capacity
- Cable: 420mm (3mm dia 4 wire shielding cable)
Logic Level Converter
LOLIN32 V1.0.0 ESP32 Rev1 Wifi Bluetooth Board
LoRa SX1278 433M 10KM Wireless Spread Spectrum Transmission Module Ra-02 SX1278 Socket IOT
- Lora Spread Spectrum Modulation Technology +20dBm-100mW
- Constant RF power output when voltage changes
- High sensitivity: low to -148dBm
- Half-duplex SPI communication Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
- 127dB RSSI dynamic range
- Automatic RF signal detection
- CAD model and ultra-high-speed AFC With CRC, up to 256 bytes of the packet engine
- Small volume dual-row stamp-hole patch package
- With shielding shell Spring antenna (Ra-01) external antenna (Ra-02)
- Wireless standard 433MHz Frequency range: 420 ~ 450MHz
- Interface: SPI GPIO
- Operating Voltage:1.8 ~ 3.7V, the typical value is 3.3V
- Current: Receiver:≦ 10.8mA (LnaBoost off, band 1) Transimit: ≦ 120mA (+ 20dBm)
- Sleep mode: 0.2μA
- Working temperature: -40 to + 85 ° C
- Storage temperature: Normal
LTH 1550-01 IR Transmitter Reciever module
- Type: reflective.
- Fast switching speed
- Pin count :4
- Reverse Voltage: 5 V
- Sensing Distance: 3.81 mm
- Maximum collector-emitter voltage: 30V
- Operating Temperature: -25 ° C to +85 ° C
- Maximum forward current: 1A
- Dimensions: 8.7mm (L) x 4.5mm (W) x 5.6mm (H)
- Maximum emitter-collector voltage: 5V
- Maximum power dissipation for input diode: 90mW
- Maximum collector current: 20mA
- Maximum power dissipation for output phototransistor: 100mW
- Non-contact switching
- For direct PC board or dual-in-line socket mounting
Magnetic Door Open Sensor – N/C Type
- Max Voltage: 100V DC
- Max Rated power: 10W
- Sensing Distance: 15-25mm
- Wire lead: 24 Awg, about 350mm long
- Rated Current: 100mA
- Connecting mode: N.C. (Normally closed)
- Easy to install
- Strong concealment
- Magnetic sensor alarm, control the switch of the circuit via the built-in magnet
- Alarm when someone intrudes into your places
- Can be used in places like apartments, hotels, offices, etc.
- Ideal for residential or commercial use.
- Designed to do embedded in the door or window frame.
- Dimension: approx. 27 x 14 x 8mm
MAX30102 Heart Rate Oxygen Pulse Breakout Sensor Module For Arduino
- Integrated LEDs, Photo Sensor, and High-Performance Analog Front -End
- Optical Heart-Rate Monitor and Pulse Oximetry Solution
- Measures absorbance of pulsing blood
- I2C interface plus INT pin
- Tiny 12.7mm x 12.7mm (0.5in x 0.5in) Board Size
- Highly integrated, small-size sensor
- Non-chest based heart-rate/SpO2 detection
- Ultra-Low-Power Operation Increases Battery Life for Wearable Devices
- Programmable Sample Rate and LED Current for Power Savings
- Ultra-Low Shutdown Current (0.7µA, typ)
- Advanced Functionality Improves Measurement Performance
- High SNR Provides Robust Motion Artifact Resilience
- Integrated Ambient Light Cancellation
- High Sample Rate Capability
- Fast Data Output Capability
MAX3232 RS232 TO TTL CONVERTER
- Chip model: MAX3232 IC
- Supply voltage: 3V -5V
- Maximum Baud Rate: up to 120kbps
- High speed, replaceable MAX232 based.
- Working mode: Full duplex
- Supports microcontroller UARTs – 5V TTL signal levels.
- Low current status LED(s)
- Very low power consumption
- Optional onboard PSU for internal/external use for a quick start out of the box.
- Power can be routed to pin 9 (if required) on the RS232 connector – useful for specific
- Operating temperature: -40 degree to +85 degree Celsius
- Dimension: 16.22*10.3*3.5mm
- Weight: 1gm