PICKIT-3 Programmer
- Full-speed USB support using Windows standard drivers
- Real-time execution
- Processors run at maximum speeds
- Built-in over-voltage/short circuit monitor
- Low voltage to 5V (1.8 to the 5V range)
- Read/write program and data memory of the microcontroller
- Diagnostic LEDs (power, active, status)
- Read/write program and data memory of the microcontroller
- 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
- Peripheral freeze at the breakpoint.
- Program up to 512K byte flash.
Pic Kit-2 Programmer
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
PICkit 3.5 Compatible Programmer with USB Cable and Jumper Wire- PIC Kit
- Type: Debugger/Programmer
- Tool/Board Application: Debugging/Programming
- MCU Supported Families: Flash-based PIC MCUs
- Core Architecture: PIC, dsPIC
- IC Product Type: In-Circuit Debugger
- USB (Full speed 12 Mbits/s interface to host PC)
- Real-time execution
- MPLAB IDE compatible
- Built-in over-voltage/short circuit monitor
- Firmware upgradeable from PC/web download
- Supports low voltage to 2.0 volts (2.0v to 6.0v range)
- Diagnostic LEDs (power, busy, error)
- Read/write program and data memory of the microcontroller
- Erase of program memory space with verification
- Freeze-peripherals at breakpoint
- Program up to 512K byte flash with the Programmer-to-Go
- Easy to use Windows-based programming
- USB Interface
Mini St-Link V2 Stlink Emulator Downloader Stm8 Stm32 with Metal Shell
- Support the full range of STM32 SWD interface debugging, simple interface (including power supply), 4 line speed, stable work; Interface definition shell directly address
- Support all series STM8 SWIM download debugging (common development environment such as IAR, STVD, etc.) are supported.
- Support the firmware upgrade automatically, to ensure that the ST company product support. When they leave the firmware has been upgraded to the latest V2. The J17. S4.
- Increase the 5 v power output, the output it can protect the I/O port, not afraid of error cause damage of ST-LINK V2.
- Easy interface to use pure copper plating 2.54 spacing horn, with 20 cm Dupont line, can deal with different target board line sequence, flexible connection;
- Use U disk aluminium alloy shell to protect the mainboard, convenient to carry, not afraid of static electricity, not afraid of tumbling.
- Material: metal + plastic
- Colour: Black/Red/Green/Pink/Gold/Grey/Blue/White( Randomly Sent )
- Power output: 5V
- simulator: about 5.6*2*0.8cm
- Debugging line: about 20cm
- Weight (kg): 0.012
AVR ISP 10 Pin to 6 Pin Adapter Board
USB AVR ISP 10 Pin Programmer | ATmega8 USB Programmer
- Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
- Support for Linux, Mac OS X and Windows XP,7,8
- 5 KB/sec maximum write speed
- Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
- 10 pin ISP interface
- Works under multiple platforms. Linux, Mac OS X and Windows are tested.
- Software controlled SCK option to support targets with low clock speed (less than 1.5MHz).
- 6 Pin Adapter board along with the programmer for Standard ISP connections.
- B-type USB Connector for power.
- Separate Two Different leds for power & programmer status.
TL866CS USB Universal Programmer EEPROM FLASH 9 Adapters Extractor for 13000 Ics
- Model: TL866CS
- With a Multi-functional ICSP interface
- 40pin ZIF socket, fully automatic, support fast mode SPI
- USB interface for both data transfer and power supply
- With over-voltage and over current protection
- Supports the serial number of the chips two times development, built-in a variety of commonly used automatic numbering functions
- English Language Support
- It can program faster than another programmer 500%~1000%
- Programming EPROM, EEPROM, FLASH, SPI, I2C,93Cxx, ICSP etc.
- Supports thousands of most popular application devices (13071+)r
- Ideally suits the portable/convenient applications, which includes: car automotive field ECU chip tuning, airbag reset, mileage, satellite devices, BIOS refreshing, Xbox, Wii gaming machines EPROM sync, PIC / MCU development, newer laptop technology and newer desktop PC etc.
- Dimensions: 4.02 in x 2.48 in x 1.22 in (10.2 cm x 6.3 cm x 3.1 cm)
- Weight: 138 g
PICKIT2 Microcontroller USB Programmer PIC KIT2 Burner
- Supported Device Families: PIC10F,PIC112F, PIC16F,PIC18F,PIC24
- Programs all current 8-, 16-, and 32-bit Flash PIC microcontrollers.
- Includes the UART Tool and Logic Tool microcontroller development utilities.
- With a portable USB power source, PICkit 2 will program the downloaded code into a PIC Microcontroller
- High-quality PCB FR4 Grade with FPT Certified
STC Automatic Programmer USB – TTL 5V 3.3V SCM Burning Programmer
- Supports 3.3V and 5V STC full range of all SCM burning procedures.
- Highest baud rate 115200
- Programmer automatically downloads without cold start, no need to frequently power down SCM.
- 4The burner with USB to TTL, USB to serial port function, can be used for USB to TTL electronic product upgrades, does not affect the normal serial communication debugging
- The success rate of STC12, STC15, STC11, STC10 series programs can be up to100%.
- Programmer uses CH340 + SCM control core.
- With 500MA self-recovery fuse, perfect to protect your computer motherboard!
- Metal aluminium shell protection burner motherboard.
- The interface definition is printed on the shell.
- When burning STC SCM, after clicking download, the light will go out, it will flash when there is data transmission, if no data transmission, it will always keep bright.
- Support win7 8 10 system (64-bit and 32-bit system)
CH341A 24 25 Series EEPROM Flash BIOS USB Programmer with Software & Driver
- USB interface
- With CH341A chip
- Support 24 EEPROM and 25 SPI flash 8pin or 16pin chip
- With 24/25 status indicator lamp
- Support USB to TTL conversion
- Support 24EEPROM and 25 SPI flash 8pin/ 16pin chip
- Recognize 25 series chip automatically
- Supports download STC series procedure of single chip
- SPI pin to support expanding the utility
- STC microcontroller supports a full range of program download
- Support expanding the utility by SPI pin
- With SOP8 SOP16 to DIP8 converter board
- Used in wide applications – PC motherboard, LCD monitor, DVD, router program reading and writing
- Supports Windows XP, Vista, Win7 and Win8 (32/64bit) system
- Provide 5V-3.3V power supply output
CH375B U-DISK Read Write Module USB interface communication SPI interface
USB TO SERIAL CP2102 CONVERTER
- Reliable and stable device
- Baud rate:300bps-1Mbps
- Supports Windows, Linux &Mac
- Compliant withUSB2.0 at a full-speed 12Mbps
- Self-power :3.0 to 3.6v
- USB bus power:4.0 to 5.25v
- Supports all handshaking and modem interface signal
- Standard USB type A male and TTL 6pin connector.
- 6pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Temperature Range: -40 to +85.
- Dimension: 42mm X 15mm.
USB TO RS-485 CONVERTER
- Small and compact size
- Baud rate:75 bps-115200bps, up to 6Mbps
- Communication distance:1200m
- Support USB 2.0 standard
- Self-powered by USB bus
- Working temperature:-40degree - +85 degree
- RS-232 serial port transmission speed of max 115.2Kbps
- Supports full handshake protocol, full-duplex data operating mode
- Directional control: Uses automatic data flow control technology, automatic identification and control of data transfer direction Load capacity: support multipoint
- Interface protection: TVS tube protection, USB self-recovery protection
- Screw Terminal Connector for easy connection
- The module requires no external power, it takes power from the USB port
- Supported Systems: Windows XP, Vista, Windows 7, Linux, macOS, and
- Dimension:6.1x1.6x1.3cm
PL2303 USB TO TTL CONVERTER
- USB specification 2.0 compliant with full-speed 12Mbps.
- Operation Level-Digital 5V
- Power Supply-External 5V
- Standard USB type A male and TTL 6pin connector.
- 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
- All handshaking and modem interface signals.
- Baud rates: 300 bps to 1.5 Mbps.
- Byte receives buffer; 640 bytes transmit buffer.
- Hardware or X-On/X-Off handshaking supported.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
- Simple serial communication.
- Router or ADSL firmware upgrade.
- Easy to use, RX to the MCU's TX; TX to the MCU's RX. and then connected to the GND. Without having to use the MAX232 conversion.
MAX3232 RS232 TO TTL CONVERTER
- Chip model: MAX3232 IC
- Supply voltage: 3V -5V
- Maximum Baud Rate: up to 120kbps
- High speed, replaceable MAX232 based.
- Working mode: Full duplex
- Supports microcontroller UARTs – 5V TTL signal levels.
- Low current status LED(s)
- Very low power consumption
- Optional onboard PSU for internal/external use for a quick start out of the box.
- Power can be routed to pin 9 (if required) on the RS232 connector – useful for specific
- Operating temperature: -40 degree to +85 degree Celsius
- Dimension: 16.22*10.3*3.5mm
- Weight: 1gm
RS232 TO RS485 CONVERTER ADAPTER
- Input: USB 2.0 Protocol
- Output: RS232 on DB9 Male connector compatible to PC RS485/RS422 on the terminal block.
- Communication Speed: 300bps to 230Kbps.
- Auto direction control for RS485- 2W data transmission.
- Plug-and-Play (Device is Hot-pluggable)
- Cable: USB 2.0 type A to type B cable.
- Galvanic Isolation of 1.5kV
- RS232/RS485 line protection: +/- 15kV ESD.
- LED Indication for Transmit Receive signals.
- Input power from the USB port
- No external power is required.
- RS232 with DB9 Female connector
- RS485 with DB9 Male connector
- Baud rate up to 230Kbps.
- Input power supply range 9-6V DC to 26.4V DC
- USB Drivers provided for Win XP, Vista, Win7, Win8
- Working Modes: Asynchronous, half-duplex, differential transmission
- Operating temperature: -10°C to 85°C,
- Relative humidity: 5% to 95%
- Transmission distance: 1.2 mile (RS-485), 5 meters(RS-232)
- Transmission Media: Common wire, double wire, UTP or Shielding Line
- Serial Port Feature: Compatible with EIA/TIA RS-232C standard and RS-485 standard
- Weight: 49gm