TF-M16P MICRO SD CARD MODULE
- Supports MP3 and WAV decoding.
- Supports a maximum of 32GB micro SD card and 32GB USB flash drive.
- Supports AD key control mode and UART RS232 serial control mode.
- 24-bit DAC output
- Supports dynamic range 90dB and SNR 85dB.
- Supports FAT16 and FAT32 file systems.
- Audio files are sorted by folders; supports up to 99 folders, and each folder can be assigned to 255 sound files.
- Supports inter-cut advertisements.
- 30 levels adjustable volume, and 6 levels adjustable EQ
- Built-in 3W amplifier that can directly drive a 3W/8Ohm speaker.
- Support maximum 3000 audio files under the root directory of the storage device
- Support random playback.
- Support maximum of 99 folders, each folder can store 255 audio files
- Supports playback of specifying folders.
PCF8574 I/O For I2C Port Interface
- Communication: I2C
- Operating Voltage: 2.5-V to 6V.
- Open-Drain Interrupt Output
- Compatible With Most Microcontrollers
- 8-bit remote I/O pins
- Up to 64 I/O ports
- Low standby current
- Operating temperature: 40 degrees C to +85 degree C
- Supports Arduino cascading, and you can use at most 8 modules to extend 64 I/O at the same time.
- Â the address can be changed by a set a toggle switch.
- Every 2 seconds, make P0-P7 port output High level, Low level, and put 3 toggle switches to ON, the address of module is 0x27.
- PCB Size: 36 x 16mm
OpAmp Breakout – LMV358
TB6612FNG Dual Motor Driver Module 1A for Arduino/Other Microcontroller
- Driver Model: TB6612FNG
- Operating voltage: 2.7 V to 5.5 V
- Limited Maximum Voltage: 15V max
- Output current: 1.2A
- Maximum Current: 3.2A (peak)
- Number of Channels: 1
- Standby control to save power
- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- All pins of the TB6612FNG broken out to 0.1 spaced pins
- Filtering capacitors on both supply lines
- Dimensions: 30 x 20 x 10mm
- Weight: 22 gm
Solid Relay Module 1 channel 5v low level trigger for Arduino
- 5V Solid State Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 3.3-5V.
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm
8 CHANNEL TTP226 CAPACITIVE TOUCH SENSOR
- On-board TTP226 capacitive touch induction IC
- On-board 8-way level indicator
- Working voltage: 2 V to 5.5 V DC
- Adjustable output mode, key output mode
- Low power consumption
- Can replace the traditional touch of a button
- Fixture screw-holes for easy positioning & installation
- Typical high Voh = 0.8VCC
- Typical Vol = 0.3VCC
- Output Sink Current: 8mA
- Output pin pull-up current: 4mA
- Response time (Low Power mode): 220mS
- Response time: 60mS
- Onboard 8-level status indicator
- Dimension: 47*46mm
A4988 STEPPER MOTOR DRIVE CONTROLLER BOARD
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor; Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
Double Analog Potentiometer Module With Slide Potentiometer Slip Adjustable Resistance For Arduino
- Dual analogue output, output 0-VCC analogue voltage signal.
- Voltage: 3.3V, 5V.
- Port: Analog.
- Resistance: 10K.
- Slide potentiometers module
- Two analogue outputs, analogue outputs 0-VCC voltage signals
- Stable and reliable performance with high-quality sliding appliances
- Platform: Arduino, MCU, ARM, and other microcontroller platforms
- Application: Raspberry Pi projects, DIY projects, Arduino projects.
- Dimensions: 91 x 21 x 30 mm
- Weight: 18 gm.
Delay Timer Switch Adjustable 0-10sec With NE555 Electrical Input 12V 10A
- Module based on the NE555 chip.
- Input voltage: DC 12V
- Adjustable time: 0-10 s
- AC Control voltage: 250V/max. 10A
- DC Control Voltage: 30V/max. 10A
- load: 2200W
- Precision Pulse Generation / Timing.
- Monostable Operation.
- Standby no power consumption
- Excellent temperature stability of 0.005%/°
- Time can be adjusted by a potentiometer, the default is 0-25 seconds
BMP280 Pressure Sensor module High Precision Arduino
- Chip:BMP280
- Operating Voltage: 1.71V to 3.6V
- Communication method: Standard IIC/SPI communication protocol
- Pin pitch: 2.54mm
- Operating Temperature: -40 to +85 deg. Celsius
- Operating Pressure: 300 hPa to 1100 hPa
- Peak current: 1.12mA
- Current consumption: 2.7µA @ 1 Hz sampling rate
- Accuracy between( 700 to 900hPa and 25 to 40 deg. C): ±0.12hPa and ±1.0m
- Package 8-pin LGA metal-lid
- Relative accuracy(950 … 1050hPa @25°C): ±0.12 hPa, equiv. to ±1 m
- RoHS compliant, halogen-fre
- Module size: 11.5mm*15mm
TTP224 4WAY
- On-board TTP224 capacitive touch sensor IC 4 keys
- 4 board-level status indicator
- Working voltage: 2.4V-5.5V
- Advanced Pins breakout, so that the output mode and working mode are selectable.
- Low power selection
- Operating Current: < 9 µA
- Fast Mode and Low Power Mode
- Various Output Mode selection
- Outputs sensing via dedicated output pins
- PCB board size: 35 (mm) x 29 (mm)