PN532 NFC MODULE
- Operating Voltage : 3.3V ~ 5v
- Support I2C, SPI, and HSU (High-Speed UART)
- I2C / UART: 3.3V ~ 24V TTL
- SPI: 3.3V TTL with 100-ohm resistors in series
- Plug and play, Arduino compatible
- Built-in PCB Antenna
- Communication distance: 5cm-7cm
- Easy to change mode: with a small SMD Toggle Switch
- Longer distance: the reading distance becomes 5~7cm,
- On-board level shifter, Standard 5V TTL for I2C and UART 3.3V TTL SPI
- Work as an RFID reader/writer
- Work as a 1443-A card or a virtual card
- Support NFC with Android phone
- Small size
- Dimensions: 42.7*40.4*4mm
Power Line Carrier Module KQ-430F
PULSE SENSOR
Rain Drop Sensor
- Operating voltage: 5V
- Provide both digital (DO) and analogue (AO) output
- Adjustable sensitivity with inbuilt potentiometer
- Output LED indicator
- Compatible with Arduino
- TTL Compatible
- Bolt holes for easy installation
- Voltage compactor IC: LM393
- Antioxidant material
- Treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance
- Comparator output signal clean waveform is good, driving ability, over 15mA
- Anti-oxidation, anti-conductivity, with long use time
- With bolt holes for easy installation
- PCB or module size: 30mm x 16mm
- Control board size: 54mm x 40mm
- Weight: approx. 8g
RDA9851 CPR9851S Bluetooth MP3 FM Module
- Supply voltage 3.2V ~ 4.2V
- Current consumption when the normal operating current 45mA, 32mA Play Pause
- Separation 50dB SNR 70dB
- supports MP3/WMA/WAV/SBC
- Wireless stereo transmission, Bluetooth phone
- BT card reader as it supports USB host so can read data from SD or MMC
- Stereo audio Line-in input
- IR remote control
- Bluetooth version Bluetooth V2.1 + EDR
- UART port for serial communication, and can customize AT communication protocol
- Integrated power management circuit
- High-speed UART interfaces, for debugging or updating software
- Support 3X3 matrix key
- Two controllable LED, support external amplifier mute function
- the internal integration 2x1W amplifier supports dual-channel amplifier output directly ( 2x6 recommended European speakers, power is about 2x0.75W)
- Modulation PSK 3Mbps, 4-DQPSK and 8DPSK
- Supports HFP / HSP, OPP, A2DP/AVRCP, PBAP profiles
- Sensitivity (0.1% BER)-82dBm
- Class2 and class3 transmit power to meet the requirements of the transmit power can provide +7 dBm maximum transmit power
- Operating temperature -20 ~ +50 degree
- Dimension: 26mm x 19mm x 2.05mm
Red TTP223 Touch button Module
- Input Voltage: 2 Volt - 5.5 Volts DC.
- Current Consumption: < 7 µA
- Low Power Mode and Fast Mode
- Start-up Calibration Delay: 0.5 Sec
- Simple, easy to use, with Auto Calibration
- Output mode is set by Jumper
- The response time max is ~ 60mS in fast mode, ~220mS at low power mode @VDD=3V.
- Sensitivity can adjust by the capacitance (0~50pF).
- Supports momentary or latching/toggle modes.
- Have two kinds of sampling length by pad option (SLRFTB pin)
- Provides Fast mode and Low Power mode selection by pad option (LPMB pin).
- Provides direct mode toggle mode by pad option (TOG pin).
- All output modes can be selected as active high or active low by pad option (AHLB pin).
- Have the maximum on-time 100sec by pad option (MOTB pin).
- Have external power-on reset pin (RST pin).
- Auto-calibration &Re-calibration period is about 4.0 sec when the key has not to be touched.
- Dimensions: 15mm x 11mm.
RFID EM18 125KHz RS232 Output
- Operating Voltage: 5V DC Supply
- Reading Distance: 6-10 cm.
- Read frequency: 125 kHz.
- EM4001 64 – bit RFID tag compatible.
- 9600bps ASCII output.
- Current : <50 mA
- Operating Frequency: 125 Khz
- This RFID Reader Module 125Khz is easy to use
- It is Low Cost
- It gives RS-232 and TTL Output
- Need a very less external component to drive
- TTL Level Compatible (Directly connected to the microcontroller)
- Small Buzzer & LED available to know about the card presence
- High-Quality PCB material & Original component only
- Dimension:32* 32* 8mm
RP203 Thermal printer with case 5V
- Model RP203 Thermal Printer Panel
- Print method: Direct thermal print and auto paper feed.
- Printing Width: 48 MM.
- Max Printer Speed: 85 mm/s (max).
- Printer Interface: TTL/RS232,
- Command System: ESC/ WH,
- Working Voltage: DC3.3V-9V,15V,
- Rich graphics/curve/text printing function,
- Printing head lifespan: >50KM,
- Paper Type: Thermal paper (With 58mm, Thickness 65+5um, diameter 35mm),
- Printer dimension: 76.8*77.4*43.5mm(w*h*d),