SI4432 WIRELESS MODULE
- Power supply: 1.8-3.6 V
- Maximum output power: 20dBm
- Data transfer rate:0.123-256kbps
- Frequency range: 433.92MHz
- Sensitivity up to 20dBm
- FSK, GFSK, and OOK modulation
- Ultra-low-consumption shutdown mode
- Digital received signal strength indication (RSSI)
- Waketime
- Automatic matching and two-way antenna switch control
- Configurable packet structure
- Preamble detection
- 64-byte send and receive data register (FIFO)
- Low power detection
- 8-bit ADC and temperature sensor
- Integrated voltage regulator
- Frequency hopping
- Operating Temperature:-20 degree +60 degrees Celsius
- Transmission Distance (Maximum):1000 meters
- Power-on reset function
- Built-in lens adjustment
- Dimension :19*19*1 mm
- Weight :0.9 g
SIM 800
- Quad-band 850/900/1800/1900MHz.
- GPRS class 2/10.
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
- High-Quality Product (Not hobby grade).
- 5V interface for direct communication with MCU kit.
- Configurable baud rate.
- Built-in SIM Cardholder.
- Built-in Network Status LED.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Low power.
SIM28 GPS Module Modem with GPS antenna
- Operating voltage: 12V DC.
- Frequency l1, 1575.42mhz
- C/a code 1.023mhz chip rate
- 16-channels GPS search engine
- Ultra-low-power design (38mA, typical)
- Compact size
- Built-in low noise, high gain active antenna
- Super-cohesive magnetic for installation
- High sensitivity (up to -152dBm type)
- Super-cohesive magnetic for installation
- Apply to host devices with USB or RS232
- Compatible with TTL serial
Sim800C GPRS/GSM Shield with Antenna
- Chip: QuadBand SIM800C GSM CHIP.
- Supply voltage range: 4 to 4.4V
- Quad-band 850/900/1800/1900MHz
- GPRS multi-slot class 12/10
- GPRS mobile station class B
- Compliant to GSM phase 2/2+
- Control via AT commands
- Configurable baud rate.
- SMA connector with GSM L Type Antenna.
- Built-in SIM Cardholder on Top Side.
- Arduino compatibility: Arduino UNO R3, Arduino Mega etc.
- Antenna type: Finger antenna.
- Output: TTL and RS232 serial output.
- Simcard holder: standard size.
- Buzzer for CALL and SMS indication
- Built-in Network, Status leds.
- Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
- Normal operation temperature: -20 °C to +55 °C.
- On-Board Buzzer for Ring Indication.
- On-Board provision for Speaker and Mic.
- Low power consumption
- Dimensions: 17.6*15.7*2.3mm
- Weight: 1.3g
SIM800L GPRS GSM Module
- Chip: SIM800L
- Operating voltage: 3.7V -4.2V
- Current : 2A
- Quad-band (850/900/1800/1900MHz) supports
- Searches for network and login automatically
- Can connect any global GSM network with 2G sim
- Miniature size
- AT command interface with auto baud detection
- Lead-out buzzer and vibration motor control port
- Scan and receive FM radio broadcast, send and receive SMS and call
- Power consumption:
- Interface: UART (max 2.8V, serial interface)
- Command support: 3G PP TS 27. 007, 27. 005 and SIMCOM enhanced AT commands
- Sim Card Slot: Micro SIM
- Temperature range: -40℃ to 85℃
Single Phase Voltage Mutual Inductor AC Active Output Module ZMPT101B 2mA
- Supply voltage: 5-30v
- Product model: ZMPT101B
- Rated input current: 2mA
- Rated output current: 2mA
- Change ratio: 1000:1000
- Phase difference: ≤20′
- Linear range: 0~1000V 0~10mA
- Linearity: ≤0.2%
- Allowable error: -0.3≤f≤0.2%
- Isolation withstand voltage: 4000V
- Uses: accurate measurement of voltage and power
- Sealing material: epoxy resin
- Installation method: printed board installation
- Working temperature: -40 to +60 degrees
- Shell material: ABS
- Voltage up to 250 volts can be measured
- Lightweight with on-board micro-precision voltage transformer
- High precision on-board op-amp circuit
- Good consistency, for voltage and power measurement
- Very efficient and accuracy
Socket Adapter Plate Board for 8 Pin Nrf24L01 Wireless Module
- Used with NRF24L01 wireless module
- Add core nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- Onboard 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
- Allows for easy connection to nRF24L01+ modules
- Small power on SMD LED indicator
- On-Board Voltage Regulator:
- Dimension: 15.3 x 11.5 x 1.2 cm
- Weight: 10 Grams
Soil Moisture Sensor
- Operating voltage: 3.3V to 5V Operating Current: 5mA.
- Dual output mode, analogue output and digital output
- Analogue output is more accurate
- Fixed bolt hole for easy installation
- Onboard power indicator (red) and digital switching output indicator (green)
- LM393 comparator chip
- Panel PCB Dimension: Approx.3cm x 1.5cm
- Soil Probe Dimension: Approx. 6cm x 3cm
- Cable Length: Approx.21cm
- Dimensions: 98 x 23 x 4.mm
- Weight (gm): 15
Solid Relay Module 1 channel 5v low level trigger for Arduino
- 5V Solid State Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 3.3-5V.
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm
Solid Relay Module 2 channel 5v low level trigger for Arduino
- 5V Solid State 2-channel Relay
- Output With resistive fuse 240V 2A.
- Input Power: 5V DC (160MA).
- Input control signal voltage: 0 - 2.5V state low relay OFF/3.3V - 5V state high relay ON
- Working current: 12.5mA.
- Trigger voltage: 2.5v
- Trigger current: 2mA.
- Rated output load: 100V to 240V AC (50Hz/ 60Hz) 2A per channel
- Rated input power: 5V, 160mA (all channels ON)
- Triggered at Low level (or Active Low)
- Separate LEDs showing the status of each Solid-State Relay
- Input control signal:
- -Low Signal (Solid-State Relay ON / CLOSE), 0V- 2V or GND
- -High Signal (Solid-State Relay OFF / OPEN), 3.3V - 5.0V or leave it floating
- Used in PLC control, home intelligent control, industry, electronic DIY etc.
- Dimension: 25mm x 34mm x 22mm
Solid Relay Module 4 channel 5v low level trigger for Arduino
- Operating Voltage: 5V
- Operating Current: 12.5mA
- Maximum Load: 2A @ 240VAC
- Static Current: 0mA
- Channels: 4 Channel.
- Switch Max frequency: 5KHz.
- Trigger Voltage Range:
- Separate LEDs showing the status of each Solid-State Relay
- Strong anti-interference ability and stable performance
- Dimension: :57 x 55 x 25mm
SOUND SENSOR
- IC Chip: LM393
- Operating voltage: 3.3V-5V
- operating current: 4-5 mA
- Voltage gain 26 dB (v=6v, f=1khz)
- Sensitivity of the microphone (1khz) :52 to 48 dB
- The impedance of the microphone: 2.2k ohm
- Frequency of microphone: 16 to 20 kHz
- Signal to noise ratio: 54 dB
- Signal output indication
- The output is digital.
- Single-channel signal output.
- With the retaining bolt hole, convenient installation.
- Output low level and the signal light when there is sound.
- Dimension:45*17*9mm
- Weight: 5gm