Development Boards
ESP8266 ESP-12E
- LDR Light Sensor on board.
- WS2812 Led on board.
- Wireless Standard: IEEE 802.11 b/g/n protocol
- Frequency Range: 2.412 - 2.484 GHz
- Serial Transmission: 110 - 921600 bps, TCP Client 5
- SDIO 2.0, SPI and UART Interface available
- PWM available
- One ADC channel is available
- Programmable GPIO available
- Wireless Network Type: STA / AP / STA + AP
- Security Type: WEP / WPA-PSK / WPA2-PSK
- Encryption Type: WEP64 / WEP128 / TKIP / AES
- Network Protocol: IPv4, TCP / UDP / FTP / HTTP
- Operating Voltage: 3.3V
- Maximum current allowed to draw per pin: 15mA
- Power down leakage current of < 10uA
- Integrated low power 32-bit MCU
- Onboard PCB Antenna
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW
- Operating Temperature: -40ºC to +125 ºC
ESP8266 ESP – 01
- 11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- +19.5dBm output power in 802.11b mode
- Power down leakage current of <10uA
- 1MB Flash Memory
- Dimensions: 25 x 15 x 11 mm (LxWxH)
- PCB Thickness: 1mm
- Weight: 2 gm
- SDIO 1.1 / 2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
- Integrated low power 32-bit CPU could be used as an application processor
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
Arduino CNC Shield v3 Engraving Machine/3D Printer/A4988 driver GRBL compatible
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825, and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin Molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
USBASP PROGRAMMER
- No special USB controller required
- Programming speed is up to 5Kbytes/sec
- Working platform: Linux, Windows, Mac OS X
- Allows to read or write the microcontroller EEPROM, firmware, fuse bits, and lock bits
- No special controllers or SMD components are needed.
- Target is supported by the SCK option with a low clock speed (<1.5MHz)
- Programming status and Bus status are easily identified
- The easy interface is achieved by Header pins for various ISP header pins
- Dimension: 63.3*20.5*10.5mm
- Weight: 15gm
Raspberry Pi Camera Module V2 – 8 Megapixel 1080p
- 8-megapixel native resolution high-quality Sony IMX219 image sensor
- Cameras are capable of 3280 x 2464 pixel static images
- Fixed focus lens on-board
- Supports 1080p30, 720p60 and 640x480p90 video
- Connects to the Raspberry Pi board via a short ribbon cable (supplied)
- Uses the Sony IMX219PQ image sensor – high-speed video imaging and high sensitivity
- All software is supported within the latest version of the Raspbian Operating System
- Supports Raspberry Pi 1,2 and 3
- Dimensions: 25mm x 23mm x 9mm
- Weight: 3.4g
ESP8266 ESP – 07
- Smallest 802.11b/g/n Wi-Fi SOC module
- Low power 32-bit CPU, can also serve as the application processor
- Up to 160MHz clock speed
- Built-in 10 bit high precision ADC
- Supports UART/GPIO/IIC/PWM/ADC
- SMD-16 package for easy welding
- Integrated Wi-Fi MAC/BB/RF/PA/LNA
- Deep sleep current as low as 20uA
- Embedded LWIP protocol stack
- Supports STA/AP/STA + AP operation mode
- Support Smart Config/AirKiss technology
- UART baudrate up to 4Mbps
- General AT commands can be used quickly
- Supports remote firmware upgrade (FOTA)
- WIFI Direct (P2P),SOFT-AP
- Built-in TCP/IP
- The AT command is perfect, efficient, concise
- Support three modes: AP, STA and AP+STA coexistence mode
- Onboard Chip Antenna
- +19.5dBm output power in 802.11b mode
- Power down leakage current of <10uA
- SDIO 1.1/2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
ESP8266 ESP-12F
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- Serial port baud rate: 115200 (default), can be modified to other values by AT command
- Serial communication format: 8N1
- Wireless Network Mode: station / softAP / SoftAP + station
- Wireless criteria: 802.11 b / g / n
- WIFI @ 2.4 GHz, support for WPA / WPA2 security mode
- +19.5dBm output power
- Compatible with ESP-12（ESP-202）
- It is very easy to develop projects with AT commands
- Surface Mount Package with 2mm Pitch Pads
- Mulitple GPIO’s for all your sensor needs
- Integrated TCP/IP protocol stac
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management unit
- Power down leakage current of <10uA
- Integrated low power 32-bit CPU could be used as an application processor
- SDIO 1.1/2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
- Both SMD and Inline package are available, and the pin pitch is 2.0mm.
LilyTiny (LilyPad ATTiny85)
- Program Memory Type: Flash
- Program Memory (KB) : 8
- CPU Speed (MIPS): 20
- Data EEPROM (bytes): 512
- Digital Communication Peripherals: 1-SPI, 1-I2C
- Capture/Compare/PWM Peripherals : 5
- Comparators: 1
- Temperature Range (C) : -40 to 85
- Operating Voltage Range (V): 1.8 to 5.5
- Pin count: 8
- Cap Touch Channels : 3
Arduino Mega 2560 Board
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 128 KB of which 4 KB used by the boot loader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
ATtiny85 Arduino-enabled Mini USB Dev Board
- Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
- Power via USB or External Source
- Onboard 5V Regulator
- Built-in USB
- 6 I/O Pins
- 8k Flash Memory (about 6k after bootloader)
- I2C and SPI (vis USI)
- PWM on 3 pins (more possible with Software PWM)
- 10-bit ADC
- ADC on 4 pins
- Power LED and Test/Status LED
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
Mega R3 +WiFi ATmega2560+ESP8266 Module CH340G Compatible For Arduino Mega
- Microcontroller:ATmega2560
- IC Wi-Fi : ESP8266
- USB-TTL converter: CH340G
- Power Out: 5V-800mA
- Power Input USB: 5V (500mA max.)
- Power Input VIN/DC Jack: 9-24V
- Power Consumption: 5V 800mA
- Logic Level: 5V
- Wi-Fi 802.11 b/g/n 2.4 GHz
- USB: Micro USB
- Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O: 54
- Analog I/O: 16
- Memory Size: 256kb
- Data RAM Type/Size: 8Kb
- Data ROM Type/Size: 4Kb
- Interface Type: SerialOTA
- Operating temperature:−40С°/+125С°
- Build in external antenna
- Dimensions:53.361×101.86mm
NODEMCU ESP8266-12 USB CH340
- 11 b/g/n Wi-Fi Direct (P2P), soft-AP
- Power input: 4.5V to 9V (10VMAX), USB-powered
- Transfer rate: 110-460800bps
- Support UART / GPIO data communication interface
- Support Smart Link Smart Networking
- Working temperature: -40°C ~ + 125°C
- Drive Type: Dual high-power H-bridge
- Don’t need to download resetting
- A great set of tools to develop ESP8266
- Flash size: 4MByte
- Integrated TCP/IP protocol stack
- Use CH340G to replace the CP2102.
- Integrated low power 32-bit CPU
- Advanced API for hardware IO, which can dramatically reduce the redundant work for configuring and manipulating hardware.
- Integrated TR switch, balun, LNA, power amplifier, and matching network
- Integrated PLL, regulators, DCXO, and power management units
- On-board USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping
NODMCU Esp8266-12 USB CP2102
- 11 b/g/n Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- CP2102 Serial / USB Chip
- +19.5dBm output power in 802.11b mode
- 4MB Flash Memory
- Integrated low power 32-bit CPU
- SDIO 1.1 / 2.0, SPI, UART
- Dimensions – 49 x 24.5 x 13mm
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- On board USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has on board 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping
- ESP-12E Processor
- Easy to use breadboard friendly form factor
- Voltage Regulator / Converter, excellent DC to DC conversion, super efficientESP-12E Processor
- Easy to use breadboard friendly form factor
Aluminum Heatsink Cooler Cooling Kit for Raspberry Pi 3/2 Model 3B+ – 3 Piece
- 3m - Sticker for best adhesiveness to the silicon.
- Best aluminium - ensures best fin efficiency and fin effectiveness.
- Colour: Black.
- Suitable for raspberry pi models a, b, b+, 2, and 3 boards.
- Can be applied with other devices such as the beaglebone.
- Dimensions:
- Teeth Number:
- Compatible with most Raspberry Pi cases
- Compatible with other devices such as the Beaglebone
- Compatible with stepper motors, motor driver boards, etc.
TL866II Plus Universal USB MiniPro USB Programmer for 15000+IC SPI Flash NAND EEPROM MCU PIC AVR
- High-Speed Programming - 12 Mbps
- Unique ultra-low power consumption
- Portable performance
- Programmable programming power supply
- Best overvoltage, overcurrent protection
- 40-pin universal pin
- Upgrade function
- 54/74F/LS/HC CMOS4000 series IC functional tests
- AVR microcontroller one-to-one soft encryption
- Unified and convenient user interface
- NAND Flash: Yes
- ISP for 24/93/25 MCU: Yes
- 25 NOR Flash Max. Capacity: 512M
- Multiprogramming: 4 programmers
- VPP Max. Voltage: 18 V
- VCC Voltage: 1.8 V to 6.5 V
- W29C020 P+V (s): 10.S+2.4S
- W25X80 P+V (s): 9.3S+1.7S
- W25W64 P+V (s): 69S+14.5S
- Device List: 15,000+
- Support simultaneously burn with 4 Programmers each computer
- Minimum Volume and the lowest Power Consumption and Do not Feel any Heat in Process.
- All chips do not need an external power supply, the low power consumption of its own to ensure that the USB port can provide enough power.
- Best internal 40 pins over-voltage protection, the strongest VCC/VPP 4-level overcurrent protection. The short-circuit do not reset the PC.
- Unique serial ICSP interface
- Test CMOS4000 74/54 series integrated circuit. Can be located in the gate circuit error.
- Chip auto serial number is the most complete and practical.
Evaluation Board For Pi
- Designed for Raspberry Pi
- UART interface: easily connects to UART modules such as RS232, RS485, USB TO UART, etc.
- 8 I/Os interface: easily connects to modules controlled by I/Os, such as 8 Push Buttons, Logic Level Converter, Mix Board, etc.
- SPI interface: easily connects to SPI modules such as AT45DBXX Data flash, L3G4200D Board, etc.
- I2C interface: easily connects to I2C modules such as PCF8574 Expansion Board, PCF8563 RTC Board, LSM303DLHC Board, etc.
- Character LCD interface: for connecting character LCDs like LCD1602
- USB connector: USB TO UART, supported by onboard converter CP2102
- Power indicator, User LEDs, User Keys
- Potentiometer: for LCD1602 contrast adjustment
- PCF8563 onboard RTC chip with battery holder and crystal
7” Touch Screen
- 800×480 high resolution.
- Viewable screen size: 155mm x 86mm
- 10 finger capacitive touch
- Supports Raspberry Pi, and the driver is provided (works with custom Raspbian directly).
- Supports BB Black, comes with related images like Angstrom.
- Supports Banana Pi / Banana Pro, which comes with related images like Ubuntu, Raspbian.
- Connects to the Raspberry Pi board using a ribbon cable connected to the DSI port.
- The Adapter board is used to power the display and convert the parallel signals from the display to the serial (DSI) port on the Raspberry Pi.
- Require the latest version of Raspbian OS to operate correctly
- Not only for mini-PCs, but it can also work as a computer monitor just like any other general HDMI screen (touch function is unavailable in this case).
- HDMI interface for displaying, USB interface for touch control.
- Back light control to lower power consumption.
- Screen Dimensions: 194mm x 110mm x 20mm
Raspberry Pi 4 (4GB)
- Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
- 2GB, 4GB or 8GB LPDDR4-3200 SDRAM (depending on model)
- 4 GHz and 5.0 GHz IEEE 802.11ac wireless, Bluetooth 5.0, BLE
- Gigabit Ethernet
- 2 USB 3.0 ports; 2 USB 2.0 ports.
- Raspberry Pi standard 40 pin GPIO header (fully backward compatible with previous boards)
- 2 × micro-HDMI ports (up to 4kp60 supported)
- 2-lane MIPI DSI display port
- 2-lane MIPI CSI camera port
- 4-pole stereo audio and composite video port
- 265 (4kp60 decode), H264 (1080p60 decode, 1080p30 encode)
- OpenGL ES 3.0 graphics
- Micro-SD card slot for loading operating system and data storage
- 5V DC via USB-C connector (minimum 3A*)
- 5V DC via GPIO header (minimum 3A*)
- Power over Ethernet (PoE) enabled (requires separate PoE HAT)
- Operating temperature: 0 – 50 degrees C ambient
ESP8266 ESP – 03 WIFI Transreceiver Wireless Module
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLLs, regulators, DCXO and power management units
- +19.5dBm output power in 802.11b mode
- Power down leakage current of <10uA
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 1.1/2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
- SDIO 2.0, SPI, UART
- 32-pin QFN package
- Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
- Integrated RISC processor, on-chip memory and external memory interfaces
- Integrated MAC/baseband processors
- Quality of Service management
- I2S interface for high fidelity audio applications
- On-chip low-dropout linear regulators for all internal supplies
- Proprietary spurious-free clock generation architecture
- Integrated WEP, TKIP, AES, and WAPI engines
UNO R3 +WiFi ATmega328P+ESP8266 Module CH340G Compatible For Arduino Uno
- Microcontroller: ATmega328IC
- Wi-Fi: ESP8266
- USB-TTL converter: CH340G
- Power Output: 5V-800mA
- Power input USB: 5V (500mA max.)
- Power input VIN/DC Jack: 9-24V
- Power Consumption: 5V 800mA
- Logic Level: 5V
- WiFi: 802.11 b/g/n 2.4 GHz
- USB type: Micro USB
- USB Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O Pins: 14
- Analog I/O pins: 6
- Memory Size: 32Mb
- Interface Type: serial
- Operating temperature: −40С°/+125С°
- Dimensions (L×W)mm: 53.34×68.58
Sensors and Modules
Drones and Drone Parts
30AMPS ESC DYS
- Input Voltage: 11.1 ~ 11.7 V.
- Constant Current: 30A (Max 40A<10s).
- BEC: 5V/3A.
- Li-Po battery: 2S ~ 3S.
- Ni-MH 4-10 CELLS Auto Detect.
- Separately voltage regulator IC for the microprocessor, providing good anti-jamming capability.
- Used with SimonK updated firmware for Multicopter
- Battery side – Male deans (T) connector.
- Motor side – Female 3.5mm gold connector.
- 30A ESC for BLDC has onboard BEC.
- Developed specifically for multi-rotor use
- Smooth, linear, and precise throttle response
- Extreme low output resistance, super current endurance
- Auto Low Battery Slow down at 3.0V/cell Lipo, cut-off at 2.9V/cell lipo.
- Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Dimension: 46* 26 * 11mm
- Weight: 23g
5045(5×4.5) SF Propellers 2CW+2CCW-2pair
- Length: 5″.
- Pitch: 4.5″.
- Weight: 22 gm.
- Shaft diameter: 5mm.
- Total length: 5 inch / 125 mm.
- Material: Glass Fiber Nylon
- Durable plastic construction provides both lightness and rigidity.
- 5045(5X4.5) Glass Fiber Nylon Bullnose Black Propellers comes with an Epoxy resin cover.
- Very strong and lightweight.
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 26 gm.
8045(8X4.5) Propeller
- Length: 8″
- Pitch: 4.5″
- Weight: 36.5g
- Shaft Diameter: 6mm
- Total Length: 177mm
- Material: ABS
- Durable plastic construction provides both lightness and rigidity.
- 1245(12X4.5) Carbon Fiber Black comes with an Epoxy resin cover.
- Very strong and lightweight.
- Includes set of plastic reducers (3, 3.17, 4, 4.70, 5, 6, 6.25 mm).
- Quick to release, quick to attach
- New design propellers, with greater aerodynamic efficiency, good lifting capacity.
- Dimensions: 30 x 6 x 4 cm
- Weight: 25gm
AfroFlight Naze32 Rev6 Flight Controller Board
- Version: 6 DOF
- Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense line
- USB on right side
- 32-bit processor running at 3.3V/72MHz (STM32F103CB).
- Up to 8 Ch. RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spectrum satellite receivers
- Built-in FrSky telemetry inverter
- Battery voltage monitoring
- SBUS Inverter built-in
- Spectrum satellite
- Modern GUI for all operating systems, Baseflight Configurator.
- Supports multiple platforms: Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
- MPU6500 : 3-Axis MEMS Gyroscope + accelerometer
- Onboard MicroUSB for setup and configuration
- BMP280 barometer
- Modern GUI for all operating systems, Baseflight Configurator.
- Sonar pads w/resistors added for direct connection to 5V sonar3.3V
- Dimensions: 36x36 mm (30.5mm Mounting)
- Weight: 5.3 grams (no headers, 7.3 grams with).
Ardupilot Mega APM 2.8 Flight Controller
- Model: APM 2.8
- Input Voltage (V): 12-16 V.
- Processor: ATMEGA2560 and ATMEGA32U-2
- Micro SD card slot: No.
- Arduino Compatible
- MPU6000 : 3-Axis MEMS Gyroscope + accelerometer
- High-performance Barometer upgraded to MS5611-01BA03, from Measurement Specialties.
- Support hundreds of 3D waypoints
- Full mission scripting with point-and-click desktop utilities
- Two-way telemetry and in-flight command using the powerful MAVLink protocol
- Powerful Ground Control Software
- Supports full "hardware-in-the-loop" simulation with Xplane and Flight Gear
- On-board 4 Megabyte Data flash chip for automatic data logging.
- Optional off-board GPS, an uBlox LEA-6H module with Compass.
- Dimensions: 70 x 45 x 15mm
- Weight: 70gm
CC3D flight Control
- Powerful STM32 32-bit microcontroller running at 90 MIPS with 128KB Flash and 20KB RAM.
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Supported by powerful OpenPilot GCS
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spectrum satellite receiver support.
- Futaba S-BUS hardware support.
- With a function of being directly plugged into the satellite receiver
- 10 PWM outputs to servos or ESC’s, or for camera stabilization
- Innovative Flexi-port technology for superior port flexibility.
- 4Mbits on-board EEPROM for configuration storage.
F450 Quadcopter Frame
- Model: F450
- Frame width: 450mm
- Frame height: 55mm
- Frame Weight: 282g
- Take-off Weight: 800g ~ 1200g
- Motor Mount Bolt Holes: 16/19mm
- Landing Gear Height: 150mm
- Landing Gear Weight: 90gm
- Made by advanced engineering material, super strong & smooth.
- High quality and strong ability of anti-fall, lower maintenance cost.
- Compact design with small numbers of components, you can assemble it by yourself quickly and easily.
- Recommended Propeller: 10x4.5in;8x4.5in
- Recommended Battery: 3S~4S LiPo
- Recommended Motor: 22x12mm (Stator size)
- Recommended ESC: 20A/30A ESC
F550 HEXACOPTER FRAME
- Model: F550
- Material: Glass Fiber + Polyamide-Nylon
- Wheelbase: 550mm
- Arm Size : 220 x 40mm
- Motor Mounting Hole Diameter: 3mm
- Landing Gear Material: ABS Plastic
- Landing Gear Height (mm): 200
- Landing Gear Color: Black
- Landing Gear Weight: 75gm
- Comes with Black, Red, and White arms for easy orientation during flying
- Plastic injection molding ensures hardness and lighter weight
- Built from high-quality glass fiber and nylon
- Easy to build and assemble
- Made by advanced engineering material, super strong & smooth
- Easy to assemble and disassemble.
- The frame is tough and durable.
- The arm equips support ridges for better and faster forward flight.
- In-built power distribution board.
- Large Center plate allows mounting of gimbals and camera for FPV and aerial photography
- Weight:624gm
FlySky 2.4Ghz 6CH Receiver
- Item Name: FS-R6B Receiver
- Brand Name: Flysky
- Power input: 4.0 -6.5 V DC
- RF power: less than 20DBm
- Modulation: GFSK
- Code type: PCM
- Sensitivity: 1024
- PWM channels: 6
- Protocol: AFHDS
- Distance: >150m
- Antenna type: Built-in antenna
- Low voltage warning: LED
- Charger port
- Certificate: CE,FCC,RoHS
- Dimension: 30*25*8mm
- Weight: 25g
Flysky CT6B 6 Channel
- Channels: 6 Channels
- Operating Voltage: 12V DC (1.5AA x 8 Battery).
- Model type: Heli, Airplane, Glider
- RF Power: Less than 20db
- Modulation: GFSK
- Code Type: 2.4Ghz No Interference
- Sensitivity: 1024.
- Bandwidth: 500 kHz.
- Default Operating Mode: Mode 2 (Left-Hand Throttle).
- Low Voltage Warning: LED
- We can programme by PC with the included software.
- Super active and passive anti-jamming capabilities.
- Very low power consumption.
- 4 Types (Airplane, Heli90, Heli120, Heli140).
- DSC Port: Yes
- Charger Port: Yes
- ANT length: 26mm
- Certificate: CE FCC
- Dimension: 190*80*240mm
- Weight: 680g
Flysky FS-i6 6 Channel
- Bandwidth (kHz): 500.
- RF Range (GHz): 2.40 ~ 2.48.
- No. of channels: 6.
- Remote controller weight (gm): 400.
- Power: 6V (1.5V AA*4).
- Antenna Length: 26mm * 2 (dual antenna).
- Transmitting Power: ≤ 20dBm.
- RF Receiver Sensitivity: -105dbm.
- Entry-level 6 channel 2.4GHz radio with telemetry capability.
- Easy to use Programming & Navigation Buttons.
- Supports Heli/Standard Wing/Elevon/V-Tail.
- 20 Model Memory.
- 8 Character Model Name.
- Trainer and charging ports.
- The backlight LCD screen displays real-time transmitter and receiver voltage.
- 4 Stick Mode Selectable.
Flysky FS-TH9X 9Channel With FS-R8B
- Transmitter: FS-TH9X Upgrade with FS-RM003 2.4GHz Module
- Receiver: FS-R8B
- Default Mode: Mode-2
- Input Power: 12V DC (1.5V x 8 AAA Battery)
- Bidirectional System
- Frequencies-Hopping
- Omni-directional High Gain Antenna
- Low Power Consumption
- Colour: Black
- Charger Port: Yes(DC Port)
- Data Output: PPM
- Channel Resolution: 4096
- Channel Delay: Better than 30us
- Display: STN VA-73 39mm LCD
- DSC port: 3.5mm:output:PPM
- Dimension:185*220*110mm
- weight: 690gm
KK-Mini FLIGHT CONTROLLER
- IC: Atmega644 PA
- Gyro/Accelerometer: Auto-level: Yes
- Input Voltage: 4.8-6.0V
- AVR interface: standard 6 pins.
- The signal from Receiver: 1520us (5 channels)
- Signal to ESC: 1520us
- LCD size: 24*18mm
- Mini buttons size: Four 3.3*4.2mm
- Mounting holes: 30.5x30.5mm
- Voltage sensor: One red positive pin header for.
- Input rail: Single row 2.54mm pitch pin header for input signal
- Firmware Version: 1.6
- Dimension: 36x36x11.5mm
Mini OSD W/ KV Team MOD For Racing F3 Naze32 Flight Controller RC Drone
- NO DC/DC converter, hence less heating
- FTDI cable compatible pinout
- Standard 6-pin ISP header
- Two LED indicators
- ATmega328P with Arduino bootloader
- MAX7456 monochrome on-screen display
- Pad for an Analog or Digital PWM RSSI signal
- Pad for the connection of a Current Sensor
- ATmega328P with Arduino bootloader
- Standalone, or with APM / Flip / Flip32+ flight controllers
- These modifications allow direct connection of two batteries (up to 4S)
- This hardware takes the hardware mods for this firmware and builds them into an RTF solution.
- This Board can be used just as a normal OSD for APM or it can be used with MWC KV Team Mod.
- Two independent power sections with an LED indicator on each.
- Solder jumpers for combining the power sections
- Solder jumper for PAL video option
- +5V 500mA regulator for up to +12V supply input
- Exposed test points for HSYNC and LOS ATmega328P with Arduino bootloader.
- Dimension: 16 x 16mm
MR.RC 12A ESC
- Input Voltage: 2-3S LIPO
- Working Current: 12A
- Burst current (10S): 15A
- BEC: 5V / 1A Programmable: Yes
- With stable performance, it is practical and durable
- Offer you high compatibility, reliability, and stability
- Throttle range can be set to be compatible with different receivers.
- Equipped with built-in linear BEC or switch BEC.
- Easy to install and convenient to use
- Play a significant role in driving and controlling the motor to complete all kinds of instructions
- Suitable for 250 Mini four-axis and F330 aircraft, etc
- Max speed: 210,000 rpm for 2-pole, 70,000 rpm for 6-pole, 35,000 rpm for 12-pole.
- Dimensions:38 x 20 x 6 mm
- Weight: 30g
Q330 Quadcopter Frame
- Colour: Black & Red
- Wheelbase: 325mm
- Frame Diameter: 330mm
- Frame Spacing: 30mm
- Recommend to use 3S 2200-4000mah Lipo battery
- Glass fibre material on centre plates
- Glass-filled nylon arms for increased strength and durability
- Lightweight arm design
- Integrated PDB for easy wiring and tidy installation
- Increased internal space for additional electronics/equipment
- Additional mounting holes for frame upgrades
- Suitable for CC3D\MWC\APM\PIXHAWK\NAZA flight control
- Recommend to use 2204/2205 + 6045propeller + 12A ESC, violate flying recommend to use 2208 motor + 20A ESC + 8045 propeller
- Dimension: 21.5*10.5*5cm
- Weight: 231g
QAV250 Quad-copter Frame
- Item name: QAV250 Frame Kit
- Arm plate thickness: 3mm
- Main material: 3k carbon fibre
- Wheelbase: 250mm
- The arm equips dampers for a safe landing.
- The arm has multiple motor mounting holes.
- Equips vibration-free mounting bracket for FPV camera.
- Recommend Propeller: 5 inch
- Recommend Motor: 1806 2204 2206
- Recommend ESC: 8A-12A
- Recommend Battery: 1300Mah-2200Mah
Motors and Motor Drivers
28BYJ-48 5V Stepper motor
- High-quality stepper motor
- Voltage: DC 5V
- Diameter: 25mm
- Step Angle: 5.625 x 1/64
- Reduction Ratio: 1/64
- Rated voltage ： 5VDC
- Number of Phase ： 4
- Speed Variation Ratio ： 1/64
- Stride Angle ： 5.625° /64
- Frequency : 100Hz
- DC resistance ： 50Ω±7%(25℃)
- Idle In-traction Frequency : > 600Hz
- Idle Out-traction Frequency : > 1000Hz
- In-traction Torque >34.3mN.m(120Hz)
- Self-positioning Torque >34.3mN.m
- Friction torque : 600-1200 gf.cm
- Pull in torque : 300 gf.cm
- Insulated resistance >10MΩ(500V)
- Insulated electricity power ：600VAC/1mA/1s
- Insulation grade ：A
- Rise in Temperature <40K(120Hz
- Noise <35dB(120Hz,No load,10cm)
48v 500W BM1418ZXF Motor Controller
- Rated Voltage: 48 Volt DC.
- Rated Power: 500W.
- Maximum Current: 30 Amps.
- Level Brake: low.
- Current limited: 30A±0.5A.
- Efficiency: ≥83%.
- Consumption: <1.5W.
- Turn The Voltage: 1-4.2V.
- Phase Angle: 120 degrees.
- Includes attachments for motor, accelerator, brake, battery, battery charging, brake light, power lock
59TYD-375-2B AC Synchronous Motor 220VAC 50HZ – 5 RPM
- RPM: 30.
- Torque: 68 kgcm.
- Voltage: 12-240 VAC.
- Input Power: <13W.
- Frequency: 50/60Hz.
- Rated Current: 100mA.
- Noise (dB): 42.
- Insulation Class: B.
- Direction of Rotation: CW OR CCW Controlled by Capacitor. "
- Main Application - beverage machine, blenders, grill, oven, office equipment, household appliances.
- Weight:580g.
5V Stepper Motor 28BYJ-48 with ULN2003
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- No of phase: 4
- Speed variation ratio: 1/64
- Pull-in torque: 300 gf.cm
- Friction torque: 600-1200 gf.cm
- DC resistance: 50Ω±7% (25°C)
- Insulated resistance: >10MΩ (500V)
- Insulated power: 600VAC/1mA/1s
- Rise in Temperature <40K(120Hz
- Noise <35dB(120Hz,No load,10cm
- Stepper motor with a standard interface, when used directly pluggable.
- Four-phase LED indicator which indicates the status of the stepper motor work.
- Compact size stepper motor perfect for small robotics applications.
5V-12V DC Brushless Motor Driver Board Controller
- Type: Voltage Regulator
- Drive voltage: DC 5-l2V
- Work current: ≤ 1.2A
- Speed range: from 0% to 100%
- Phase inversion Control
- Offers Voltage polarity protection and Overcurrent Protection
- Suitable for hard brushless motor, brushless motor drive and other miniature 3 / 4 wire brushless motor without hall
A4988 Stepper Motor
- Operating voltage supply: 8 V to 35 V
- Continuous current per phase: 1 Amp
- Maximum current per phase: 2 Amp
- Minimum logic voltage: 3V
- Maximum logic voltage: 5.5V
- Microstep resolutions: Full, 1/2, 1/4, 1/8, and 1/16
- Logic Voltage supply: 3.3 V to 5 V
- Compatible with 3V3 and 5V microcontrollers
- Our Board comes with 0.1 Ohm Sensor resistors
- Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
- The Correct current decay mode (fast decay or slow decay) is selected by chopping the control
- Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
BM1418ZXF 48V 750W Controller for Brushless DC Motor
- Rated Voltage: 48V.
- Rated Output Power: 750W
- Speed after Reduction: 480 RPM
- Rated Speed: 2800 RPM
- Gear Ratio: 1:6
- Throttle: 1-4V.
- Full Load Current: 20A
- No Load Current: 5A
- Rated Torque: 15.36 N.m.
- Load Capacity: Up to 350 KG
- Small and Medium-size E-Tricycle
- Short voltage protection: 31.5±0.5V/42±0.5V.
- Colour: silver.
- Casing material: Aluminium.
- Dimension: 105 x 65 x 32mm
DC 6-30V 6V 12V 24V 5A PWM Motor Speed Controller with Digital Display
- Material: ABS
- Colour: Black
- Input power supply voltage: 6V-30V DC
- Output current: rated current 5A (maximum 8A, can not be extended)
- PWM frequency: 13kHz
- Duty cycle adjustable: 0%-100%
- Adjustable speed range: 0%-100%
- Fine workmanship and good performance.
- Digital display for duty ratio input
- Easy to use.
- Long service life.
- Suitable for the DC motor (or DC load) within 5A, Peak current 8A.
- Dimension: 78*42*25mm
DM556 Digital Stepper Motor Driver with Micro Stepping 20 to 50V 5.6A
- Good high-speed performance
- Supply voltage: +50VDC
- Output current from 0.5A to 5.6A
- Pulse input frequency up to 200 kHz
- Extremely cost-effective
- Automatic idle-current reduction
- Self-test and Auto-configuration technology TTL compatible and optically isolated input
- Micro step resolutions programmable, from full-step to 102,400 steps/rev
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Anti-Resonance provides optimum torque and nulls mid-range instability
- Extra-low motor noise offers excellent quietness
- Over-voltage, over-current protection and phase error protection
FEETECH FT6560M 65kg Large Scale High Torque Servo
- Model: FT6560M.
- Operating Speed6.0v 0.15 sec/60°.
- Operating Speed7.4v 0.13 sec/60°.
- Stall Torque 6.0v 48 kg.cm.
- Stall Torque 7.4v 62 kg.cm.
- Motor: carbon.
- Control Way: Digital.
- Cable Length: 20cm.
- Gear: 5 metal gears.
- Bearing: 2BB.
- Dead band: 4us.
- Working frequency: 330hz.
- Wire/Color: JR 265 mm/ -Brown +Red S Orange.
- Dimensions: 65.8X30.2X57.4mm.
- Weight: 200 g.
L298N MOTOR DRIVER
- Driver model: L298N 2A
- Driver chip: Double H bridge L298N
- Motor supply voltage: 46V(maximum)
- Motor supply current: 2A(maximum)
- Logic voltage: 5v
- Driver voltage: 5V-35V
- Driver current: 2A
- Logical current: 0-36mA
- Maximum power: 25W
- Current sensor for each motor
- LED indication for power status
- Heat sink for better performance
- Operating temperature: -25 degrees to 135 degrees Celsius
- Can be interfaced with simple manual switches, TTL logic gates, relays, etc.
- Dimension: 55*60*30mm
- Weight: 33gm
Leadshine DM320C
- Supply voltage up to +30 VDC
- Output current programmable, from 0.3A to 2.0A
- Pulse input frequency up to 70 kHz
- TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protection
- Anti-Resonance provides optimum torque and nulls mid-range instability
- Self-test and Auto-configuration technology offers optimum responses with different motors
- Microstep resolutions programmable, from full-step to 102,400 steps/rev
- Support PUL/DIR and CW/CCW modes
- Over-voltage, over-current, phase-error protection
- Its unique features make the DM320C an ideal solution for applications that require low-speed smoothness
Leadshine DMA860H
- Input voltage: Up to +80VAC or +110VDC.
- Output current Up to 7.2A.
- Pulse input frequency up to 300 KHz.
- Automatic idle-current reduction.
- Over-voltage, over-current protection.
- Suitable for 2-phase and 4-phase motors.
- Support PUL/DIR and CW/CCW modes.
- Operating Temperature : 70 C.
- High performance, cost-effective
- Self-adjustment technology
- Pure-sinusoidal current control technology
- TTL compatible and optically isolated input
- 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
MACH3 interface board
- Compatible Stepper Motor Driver - Max 5 2-phase Microstep controllers
- Driver type - Pulse and Direction signal control
- Wide input voltage range: 12-24V, and with anti-reverse function.
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Maximum support 5-axis stepper motor driver controllers
- Output 0-10V analogue voltage for the inverter to control the spindle speed.
- All the way to the relay output port, control spindle switch. Output port P17 mouth.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
- Weight - Approx. 75g
- Dimensions - 90 * 70 * 20mm
MARSPOWER MX1806 2280KV BLDC Motor
- VK: 2280
- Max thrust: 460g
- No of cells: 2-3S
- Framework: 12N14P
- Suitable Propeller: 5-6”
- Shaft: 2mm
- Minimum ESC Specification: 12A Suggested
- Durable with high quality
- The 0.2mm core to lower load temperature and increase efficiency
- Range of use for DJI F330 ZMR250 H250
- Do every single motor balancing test
- Japan NMB bearings provide low noise and long life
- 2mm spindle selection of Kawasaki, Japan, more efficient, less heat
- NdFeB magnets temperature selection
- MX1806 (positive thread motor)
- FPV all configurations life 7-8 minutes!
- Easy to loosen the nut bombing risk!
- Low centre of gravity design
- Long-endurance design
- Dimension: 26.7*23mm
- Weight: 18gm
N20 Model – 40 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio: 1:380.
- Nominal Voltage: 6v.
- Voltage Range: 3v to 12v.
- RPM: 40.
- No-load Current: 40mA.
- Stall Current: 550mA.
- Stall Torque: 7500 g-cm.
- Ideal for making robots
- Lightweight, high torque, and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft
N20 Model – 500 RPM DC 12V Torque Gearbox Micro Gear Box Motor
- Reduction ratio - 1:30.
- Nominal Voltage - 6v
- Voltage Range - 3v to 12v
- RPM - 500
- No-load Current - 40mA
- Stall Current - 550mA
- Stall Torque - 400 g-cm
- Ideal for making robots
- Lightweight, high torque and low RPM.
- Fine craftsmanship, long-lasting, not easy to wear.
- Can easily mount a wheel on the motor’s output shaft.
NEMA 17 1.6 kgcm
- Operating Voltage : 12~16 V
- Step Angle : 1.8°
- Holding Torque : 1.6 KgCm
- Operating Voltage : 12 - 16 volts
- Supply Current (A) :0.31 Ampere
- Number of Leads : 6
- Frame Size (mm) : 42 x 42
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 20
- Input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- Provides good starting, stopping and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Planetary Gear DC Motor with Encoder 12V 11 RPM 10 N-m Torque – TPG36555123000-264KE
• Model: TPG36555123000-264KE
• Motor Type: DC Carbon Brush Motor.
• Gear Ratio: 264: 1.
• Operating Voltage: 12. V DC
• Rated Current: 0.800.A
• Rated Base Motor: 3000.RPM
• Rated Speed: 11 RPM
• Rated Torque: 10 N-m
• Operating Temperature: -40 °C ～ +100°C.
• Opt. Relative Humidity: 20% ～ 85% RH
• Gear Material: Powder Metallurgy, Steel, POM.
• Housing Material: Metal.
• Motor Body Size (Diameter): 36. mm
• Motor Length: 11.5mm
• Shaft Diameter: 8mm
• Shaft Length: 20mm
• Shaft Type: D-type.
• Motor Weight: 500 gm
• Brushed permanent magnet DC motor.
• Variable speed and reversible.
• Planetary Gear Box.
• Standard brush life of 2000+hours
Planetary Gear DC Motor with Encoder 12V 315 RPM 2.5 N-m Torque – TPG36555126000-19KE
- Model: TPG36555126000-19KE
- Motor Type: DC Carbon Brush Motor.
- Operating Voltage: 12. V DC
- Rated Current: 0.800.A
- Rated Base Motor: RPM
- Rated Speed: 315 RPM
- Rated Torque: 5N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 36. mm
- Motor Length: 10.8mm
- Shaft Diameter: 8mm
- Shaft Length: 20mm
- Shaft Type: D-type.
- Motor Weight: 500 gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+hours
Planetary Gear DC Motor with Encoder 12V 435 RPM 2 N-m Torque – TPG36555126000-13.7KE
- Model: TPG36555126000-13.7KE .
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio: 13.7: 1.
- Operating Voltage: 12. V DC
- Rated Current: 0.800.A
- Rated Base Motor: RPM
- Rated Speed: 435 RPM
- Rated Torque: 2N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 36. mm
- Motor Length: 10.8mm
- Shaft Diameter: 8mm
- Shaft Length: 20mm
- Shaft Type: D-type.
- Motor Weight: 500 gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+hours
Planetary Gear DC Motor with Encoder 12V 500 RPM 0.5 N-m Torque – TPG28395126000-12KE
- Model: TPG28M395-12K.
- Motor Type: DC Carbon Brush Motor.
- Gear Ratio: 12: 1.
- Operating Voltage: 12.V DC
- Rated Current: 0.750.A
- Rated Base Motor: RPM
- Rated Speed: 500 RPM
- Rated Torque: 5 N-m
- Operating Temperature: -40 °C ～ +100°C.
- Relative Humidity: 20% ～ 85% RH
- Gear Material: Powder Metallurgy, Steel, POM.
- Housing Material: Metal.
- Motor Body Size (Diameter): 28.mm
- Motor Length: 8.8mm
- Shaft Diameter: 6mm
- Shaft Length: 13mm
- Shaft Type: D-type.
- Motor Weight: 230. gm
- Brushed permanent magnet DC motor.
- Variable speed and reversible.
- Planetary Gear Box.
- Standard brush life of 2000+hours
Industrial Components
1 or 4 Inch Keyless Drill Bit Chuck Hex Shank Adapter Converter Quick Change
- Material: Drop Forged #45 Carbon Steel.
- Colour: Silver and Black
- Connecting Shank: 1/4 inch (6mm)
- Clamping Range: 0. 3- 6. 5mm
- Instantly convert impact driver to hold non-quick change drill & driver bits
- Ideal for working in tight places
- Turns any 1/4" cordless power screwdriver into a drill or grinder to quickly switch tasks and keep the job moving
- Keyless chuck finger-tightens for easy bit changes unlimited use in
- Unlimited Use in Automotive, Garages, Warehouses, Offices, Homes Etc.
- Dimension: approx. 6*2.9cm
12V SOLENOID LOCK
- Body Material: Iron
- Holding force: 0.25 kg
- Operating Voltage: 12V.
- Rated Current: 0.8 A.
- Power: 9.6 Watt
- Energized forms: intermittent
- Cable Length: 35 cm (with connector).
- Draws 650mA at 12V, 500 mA at 9V when activated
- High quality ultra-compact electric lock
- Unlocking time: 1s
- Rustproof, durable, safe, convenient to use.
- Suction tightly sucks the iron, thus locking the door.
- Applicable for being installed in the escape door or
- Dimensions: 54 x 42 x 28 mm
- Weight: 150 gm.
12V SOLENOID VALVE
- Voltage: 12V DC
- Power consumption: 5.4W
- Rated Current: 0.6A
- Operation Mode: NC (Normally Closed)
- Pressure: 0.02 – 0.8MPa
- Max fluid temperature: 100°C
- 1/2" BSP male connections, 2-way normally closed solenoid valve, 12V DC
- Valve orifice: DN 10 mm
- Electrical connection: Fast-on tags
- Compact and convenient.
- Easily installed and serviced
- Precise and reliable.
- Pressure-regulating valve
- Suitable for fluids like water, oil, air.
150mm 6 inch LCD Digital Electronic Vernier Caliper
- Measuring range: 0–100 mm.
- Resolution: 0.1mm.
- Repeatability: 0.1mm.
- Accuracy: + 0.1 mm.
- Maximum measurement speed: 1m/s.
- Power: 1 x 1.5V SR44 (silver oxide cell) battery
- Material: Carbon Fiber
- Internal, external and height dimensions can be easily and accurately measured.
- Zero setting in any position.
- With easy to read large LCD display.
- Handy conversion chart at the back.
- Ideal tool for a broad range of industrial and automotive applications.
- Dimension: 240 x 80 x 12mm
24V Dc 1/2″ Brass Electric Solenoid Valve Water Air Fuels Gas Normal Closed New
- Working Medium: Air, Water, Oil, Gas
- Voltage: DC24V, ±10%
- Operating Type: Directly driven
- State: Normally closed
- Flow bore: 16mm
- CV: 4.8
- Pipe Size: 1/2"
- Operating Viscosity: Under 20CST
- Operating Pressure: 0-10 Kg/cm²
- Working Temperature: -5 degrees to 80 degrees C
- Voltage: DC24V, ±10%
- Valve Body: Brass
- Electric lifting magnet
- Powerful and compact
- Smooth and flat surface
3 Wires 0.28 inch Digital Voltmeter DC 0-100V Red Light LED Panel Voltage Meter
- Display ON Voltage: 3 V
- Measurable Voltage Range: 0 to 100V
- Current Consumption: 10 mA
- Refresh Speed: 200ms (one time)
- Minimum Input: 3 V
- Highest Input: 30 V
- Accuracy: 0.1 V
- Colour: Red
- Wires: 3
- Operating Temperature: -10 to 60 degrees C
- Holes for Mounting: 3 mm
- Very small and lightweight voltmeter module.
- Very handy and easy to use.
- Red LED display.
- Best operates in the working voltage range of 5V to 24V
- Dimension: 13*30*9mm
- Weight: 3gm
30mm-120mm Adjustable Circle Cutter Metal Wood Circle Hole Saw Drill Bit Cutter
- Material: Alloy Steel
- Shape: Air Plane
- Adjustment Range: 30mm-120mm
- Total Length: 16cm/6.30" (Approx.)
- Heavy-duty woodworking construction with longest tool life
- Multi-functions, Very convenient and affordable.
- Having adjustable two sharp blades on both sides of the measure-bars.
- Adjustable Plane type design.
- Adjustable Capacity 30mm - 120mm
- Comes with Set of Cutter + Blades + Centre Drills
- Comes with Hex Key and Center Drill Bit
- 2 Changeable Centre bits for thinner or thicker materials freely.
- Used to cut many kinds of materials, such as Plywood, Hardwood, Laminates, Composite, Rubber, Plastic, etc
AC 80- 300V LCD Digital Voltmeter Eu Plug Electric Pen Meters
- Model: DM55 1
- Colour: White
- Material: ABS
- Measuring Accuracy: ±1.5%, ±2 digit
- Number of Digits: 3 Digits
- LCD size: 3.6 * 1.8cm
- LCD Display Colour: Blue
- Suitable for measuring the AC voltage in many places, such as offices, factories, laboratories, households and so on
- A plug-in digital voltmeter is widely used in AC 80-300V detection
- Digit Measuring Range: AC 80 300v
- Consume Power: <1w (about every 1200hours consume 1 kilowatt hour)
- Plug Style: Eu
- Dimension: 53 * 38 * 60mm
- Weight: 37g
Chrome Steel Extended 1 or 4 Inch Hex Shank Quick Change Adapter Bit Drill Chuck
- Material: Chrome Vanadium steel
- Shank Type: Hex Shank
- Diameter: 6. 35mm(1/4)
- Length: 60mm.
- Can be used for prolonging different kinds of screwdrivers.
- Built-in magnetic, fast, fastening, greatly improve work efficiency.
- Suitable for electric drill, screwdriver, wind batch transfer using to play the role of releasing bit holder.
- The interface comes with a locking function
- Extension rod can only be fitted with a single-ended mouthpiece, but not a double-ended mouthpiece.
- Dimension: 60mm
- Weight: 0.025kg
DC 12V KK-P25/20 5KG Lifting Solenoid Electromagnet
- Operating Voltage: 12V DC.
- Lifting Capacity: 5KG.
- Electric lifting magnet.
- Powerful and compact.
- Smooth and flat surface.
- Low consumption and reliability.
- The ambient temperature within 130 degrees.
- High mechanical strength and excellent durability
- Minimized residual magnetic force
- Lightweight, compact design for space-saving.
- Dimension: 25 x 20 mm.
DC 24V Solenoid Air Valve 5 Port 2 Position 4V210 08
- Media: air.
- Working Pressure: 0. 17~0. 7Mpa max.
- Pressure resistance: 1. 05Mpa.
- Fluid temperature: 5 50¡¦
- Effective Sectional area 16mm2 (cv=0. 78)
- Joint pipe bore inlet=outlet=1/4 inch,
- Exhaust=1/8 inch.
- Hole: r/s thread (g1/8): approx. 9. 7Mm or 0. 38Inch,
- P Thread (g1/4): approx. 12. 7Mm or 0. 5Inch
- A, B Thread (g1/4): approx. 12. 7Mm or 0. 5Inch.
- Valve body: brass.
Diamond Coated Core Hole Saw Drill Bit Tools for Tiles Marble Glass (5mm 6mm 8mm 10mm 12mm) – Set of 5
- Type: Core drill bit.
- Material: Nickel Plated
- Coating: Diamond
- Diy supplies: Electrical
- Perfect for Cutting Accurate Holes in Glass And Ceramics.
- Heavy-duty hole saws plated with nickel with diamond coating gives superior performance on ceramic tile and similar material.
- Sizes: 5/32", 1/4", 5/16", 3/8", 1/2"(5mm 6mm 8mm 10mm 12mm)
Digital LCD Ampere Voltage Meter Ammeter Voltmeter AC 80 300V 100A
- Material: ABS
- Colour: White
- Voltage Measurement Range: AC 80-300V
- Current Measurement Range: AC 0-100.0A
- Power supply: < 0.2V*A
- Installation: Embedded installation
- Accuracy: 1% ± 2digit
- Measurement speed: about 2 times per second
- Display Type: LCD with blue backlight
- Operating Temperature: 10deg. C ~65deg. C
- Operating Humidity: 35~85 per cent RH
- Current Transformer: included
- Widely used in substation automation, distribution automation, test equipment, voltage regulator and so on
- Dimension: Approx. 7x4.1x3.2cm
Digital Voltmeter Ammeter DC 0-100V 10A Dual LED Monitor Panel, Red and Blue
- Input Voltage: 4.5V to 30V DC
- Input Current: <= 20mA
- Display Colour: Red (Voltage), Blue (Current)
- Measuring Voltage Range: 0V to 100V DC
- Measuring Current Range: 0A to 10A
- Measurement Accuracy: 1%
- Minimum Voltage Resolution: 0.1V
- Minimum Current Resolution: 0.01A
- Voltage error: ±0.1%
- Current error: ±1%
- Working temperature: -10℃ to 65℃. Blue
- 28’’ device with 5 wires divided into 2 sets.
- Black, Red are for the power supply and 3 wires to measure the Voltage and Current.
- Dimension: 48mm x 29mm x 22mm
Drillpro 290mm Drill Bits Accessories Electric Drill Tools
- Material: Plastic + metal.
- Full length: 295mm.
- Flexible shaft dimensions:
- Hex shank: 6.35mm (1/4"").
- Inner hexagon head: 6.35mm (1/4").
- Colour: Black.
- This Flexible shaft can be used for general formula hand drill chuck
- Used for the electric screwdriver.
- Flexible shaft head can be mounted hexagonal shank (1/4 handle) the first batch
- Widely used in computer chassis, electrical cabinets, furniture, electrical appliances and other narrow space screwdriver cannot work in an environment operations.
JF-0630B DC 24 V 300mA 10mm 6N Push Pull Solenoid Electromagnet
- Model: JF-0630B
- Rated Voltage: DC 24V
- Type: Pull Push
- Rated Current: 300mA
- Force & Stroke: 6N/10mm
- Body Size: 30 x 20 x 18mm
- Plunger Bar Size : 7 x 58mm
- Mounting Hole Diameter: 2.5mm
- Cable Length: 19cm
- Weight: 46g
- Iron Body Material
- High quality ultra-compact electric lock.
- Rustproof, durable, safe, convenient to use.
- Suction tightly sucks the iron, thus locking the door.
- Designed with the open frame type and mount board, high power.
- being installed in the escape door or fire door electronic controlled system.
- Adopts the principle of electric magnetism, when the current through the silicon, the electromagnetic lock will achieve a strong
Mini 0.36 Digital Voltmeter DC 4.7-32V 2 Wires Voltage Panel Meter LED Display – Red
- Measurement range: 4.7V to 30V DC
- Only 2 wires, derives supply from the source
- Operation current: < 30mA
- Display colour: RED
- Measurement Error tolerance: +/- 2 percent
- Distance between mounting holes: 26mm
- Current Consumption: < 15 mA.
- Accuracy: 0.1 V.
- Wire length: 18cm.
- Refresh Speed : Approx. 200mS/time.
- Very small and lightweight voltmeter module.
- Very handy and easy to use.
- LED display.
- Best operates in the working voltage range of 5V to 24V
- Dimension: 30mm x 12mm x 8.5mm
Mini Electric Drill Chuck 0.3-4mm Jto Taper-Mounted Lathe PCB Drill Press
- High precision screw thread and tapered hole.
- Strong impact resistance.
- Compatible with impact drill and different power electric drill.
- jt0 taper the biggest end of diameter: 6. 350mm
- jt0 taper the smallest end of diameter: 5. 800mm
- Outer diameter: 21. 5mm
- Drill Clip aperture: 6mm
- Taper type outside diameter drill chuck: 21mm
- Clamping range: 0. 3mm-4mm drill,
- Maximum clamping: 4.2mm
- Fit motor shaft diameter 3. 17mm
- Connection size: jt0 (inner hole diameter is 6 mm) for milling machine, lathe, drilling machine, woodworking machine
Pack of 50 pcs Standard Metal HSS Twist Drill Bits Straight Shank
- Model: Twist Drill Bit
- Surface Treatment: Titanium Coating
- Design: straight shank
- Material: HSS
- Size: 1mm*34mm, 1.5mm*38mm, 2mm*45mm, 2.5mm*55mm, 3.0mm*65mm
- Suitable for wood, aluminium, plastic.
- Straight shank design is more suitable for many electric drills sharp and twisted flute will make the drilling be more easy and effortless
Soldering Iron Stand
- Universal holder
- Superior sponge Soldering Stand
- Nickel-plated wide spring holder
- Robust and powerful base to uphold the weight of soldering irons varying from 30w, 35w, 40w, 50w, 60w and 75w
- The wide spring holder provides plentiful room for holding the soldering iron support.
- Hollow base - Only sides are in contact with the work surface
- Spring Holder Length: 100mm
- Centre Hole Dia. : 23mm
- Inner Cup Size: 32mm
- Size : 10 x 6.7 x 1.8 cm
- Weight: 106 gm.
Solid State Relay Module DC To AC SSR-40DA 3-32VDC/24-380VAC 40A
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 40A.
- Working voltage: 250V.
- Material: plastic + metal.
- Loading current: 40A
- Control current: 3-25mA DC
- On voltage: ≤1.5V AC
- One-off Time: ≤10ms
- Off Leakage Current: ≤2mA
- Dielectrics voltage-resistance: 2500VAC
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
Solid State Relay Module SSR-25DA 25A /250V 3-32V DC Input 24-380VAC Output
- Control mode: DC-AC
- Input voltage: 3-32V DC.
- Output voltage: 24-380V AC.
- Output current: 25A.
- Working voltage: 250V.
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Dimension: 6. 5Cm x 4. 5Cm x 2. 2Cm
Solid State Relay SSR-40DD 40A 3-32V DC to 5-60V DC SSR 40DD Relay Solid State
- Model: SSR-40 DD.
- Control mode: DC-DC
- Input voltage: 3-32V DC.
- Output voltage: 5-60V DC.
- Output current: 40A.
- On voltage: ≤1v.
- One-off time: ≤10ms.
- Off leakage current: ≤2ma.
- Loading current: 40A
- Control current: 3-25mA DC
- Material: plastic + metal.
- Environment temperature: -30 to +75
- Long service life and high reliability.
- Reduced electromagnetic interference.
- Highly reliable, compact size designed to offer users maximum simplicity.
- Weight: 0. 106Kg.
Triangular Shank HSS Step Cone Drill Titanium Bit Hole Cutter 1 or 4 1 3 or 8 Inch
- Material: High-Speed Steel Hss Steel.
- Super-hard titanium coating lasts up to six times longer than high-speed steel
- The self-starting point starts on contact
- Titanium reduces heat for longer life
- Anti-skid tip eliminates the need for centre punching or pilot hole drilling.
- Deburring, chamfering, elliptic hole enlargement, twist drill, the function of them was unable, but it is possible
- Applicable scope: woodworking punch
- Size: 1/4 1 3/8 (1/3/1/5/3/7/1 1/1 1/1 3/8)
Fast Delivery
Customer Support
Safe and Clean
Quality Products